Basic telecommunications access method

Basic Telecommunications Access Method (BTAM)[1] was a low-level programming interface specified by IBM for use on the IBM System/360 for start-stop and binary synchronous telecommunications terminals. Later, IBM specified higher-level interfaces QTAM and TCAM.

BTAM was superseded by VTAM for Systems Network Architecture (SNA) devices.

BTAM requires the application program or transaction processing system to handle almost every detail of the protocol. This is harder than using a higher-layer protocol, but it permits interfacing to non-standard devices in non-standard ways. BTAM continued to be supported in later iterations of the system architecture. IBM finally withdrew support for BTAM in 2000.

An access method for terminals

BTAM was an access method for interactively communicating with remote terminals, usually connected through a front end processor such as a 270x, although support for local 3270 terminals was included. BTAM dynamically built CCW's for reading, writing and "polling" terminals and dealt with specific responses from those terminals, according to the success or failure of the communication channel.

Key role in transaction processing systems

BTAM was a key component in IBM's early transaction processing systems such as MTCS, CICS and IMS and underpinned the rise of online transaction processing for many large commercial banks and insurance companies. It was not unusual for BTAM and later developed access methods (such as VTAM) to co-exist, supporting different devices simultaneously under the same transaction processing system.

Programming

Material in this section taken from IBM System/360 Operating System Basic Telecommunications Access Method; GC30-2004-6.[2]

BTAM programming required detailed knowledge of the characteristics of the specific terminals to be used.

THE DCB macro was used to define a communications line group:
dcbname DCB DSORG=CX...
DEVD=BS could be coded to specify a Bisync line. Many other operands specified unique characteristics of the attached terminals.

A terminal list, specified by the DFTRMLST macro, identified the terminals attached to the line. This macro specified the line characteristics—start-stop, bisync, point-to-point, multipoint, leased line or dial — and the type of polling required— wrap around or open. The polling characters or telephone number used to identify each specific remote device on the line was coded. The CHGNTRY macro could be used to modify information for a specific device in the list during execution. A wrap-around polling list would cause each device in the list to be polled sequentially by the channel until a response was received, This reduced the load on the CPU for continuous polling.

The programmer could specify a buffer pool, a data structure used to hold messages transmitted to or from the terminals. BTAM could construct the pool automatically or the programmer could construct the pool in various ways. The BUILD macro would format the pool in static or dynamic storage previously acquired, or the GETPOOL macro would acquire and format storage automatically. For read operations BTAM would automatically obtain one or more buffers from the pool and store the received message. For a write operation the programmer needed to code REQBUF to obtain the number of buffers necessary to build the output message. In either case the RELBUF was used to free the buffers on completion of the read or write.

Tha ASMTRTAB and TRNSLATE included translation tables and translated to and from non EBCDIC data.

The standard OS/360 OPEN and CLOSE macros were used to initiate and terminate processing of a BTAM line. The LOPEN macro could reinitialize a line that, for whatever reason, failed to open successfully.

BTAM provided a large number of options for the READ and WRITE macros, depending on the line and terminal types and the current status. These were such operations as "read initial with reset", "read conversational", "read repeat", "write initial", "write break", and "write continue transparent". These were specified by codes, such as READ decbaddr,TI,... for a "read initial." The read or write operation was executed asynchronously by the channel. Following a read or write, a WAIT or TWAIT macro was required to wait for completion and retrieve ending status.

The RESETPL macro canceled an outstanding read and/or stopped polling on a line.

Supported devices

Amongst many other devices supported, BTAM handled:

References

  1. ↑ IBM System/360 Operating System Basic Telecommunications Access Method Program Logic Manual (PDF). IBM. February 1972. GY30-2001-5.
  2. ↑ IBM System/360 Operating System Basic Telecommunications Access Method (PDF). IBM. September 1972. GC30-2004-6.
This article is issued from Wikipedia - version of the Saturday, December 26, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.