Corvette leaf spring

Corvette leaf spring commonly refers to a type of independent suspension which utilizes a fiber-reinforced plastic (FRP) mono-leaf spring instead of more conventional coil springs. It is named after the American sports car Chevrolet Corvette[1] for which it was originally developed and first utilized.[2][3][4][5][6] A notable characteristic of this suspension configuration is the mounting of the mono-leaf spring such that it can serve as both ride spring and anti-roll spring. In contrast to many applications of leaf springs in automotive suspension designs, this type does not use the spring as a locating link. While this suspension type is most notably associated with several generations of the Chevrolet Corvette the design has been used in other production General Motors cars as well as vehicles from Volvo and Mercedes-Benz. Fiat and Zastava produced cars with a similar configuration using a multi-leaf steel spring in place of the FRP mono-leaf spring. Several manufactures and suppliers have since researched, adapted and utilized variations of this suspension design.

Design

The C5 Corvette's rear suspension

This suspension configuration is independent and utilizes control arms to define the motion of the wheel as the suspension is compressed. The coil springs are replaced with a single, FRP spring which spans the width of the car. As in independent suspension systems using coil springs, and unlike the common leaf spring supported Hotchkiss rear axle, the suspension kinematics are defined only by the control arms. Because the movement of one wheel is not determined by the position of the other this is an independent suspension type.

As in a coil spring suspension design, the FRP mono-leaf spring supports the weight of the vehicle. However, the FRP leaf springs differ from steel coils and traditional steel multi-leaf springs in a number of significant ways. The FRP plastic springs have 4.3–5.5 times the strain energy storage per weight as compared to steel.[7] This results in a lighter spring for a given application. The single FRP mono-leaf front spring used on the fourth generation Corvette weights 33 percent of the weight of an equivalent set of coil springs.[8] FRP spring weight savings as compared to conventional leaf springs in similar applications are even greater. The third generation Corvette offered an optional FRP mono-leaf spring as an alternative to the standard multi-leaf steel spring. The 22-kilogram (48 lb) steel spring was replaced by a 3-kilogram (7 lb) mono-leaf spring.[9] Volvo claims a weight savings of 5 kilograms (10 lb) by using a FRP spring in the rear suspension of the second generation XC90 as compared to designs using coil springs.[10] In addition to reduction in vehicle weight, the weight of the spring is partly unsprung mass.

The relative sliding movement of the leaves of a multi-leaf steel spring results in stiction based hysteresis with respect to spring compression. This stiction reduces suspension compliance and can compromise both ride quality and handling.[11] Lacking individual leaves, the mono-leaf spring avoids stiction.

FRP springs are advertised as having exceptional cycle life and corrosion resistance.[8] A GM test comparing the third generation Corvette springs found the multi-leaf steel springs failed spec after 200,000 full travel cycles. The replacement FRP leaf spring showed no loss of performance after two million full cycles.[9]

Packaging is cited as both an advantage and disadvantage of the transverse FRP leaf spring as compared to coil springs depending on the application. The FRP spring is typically packed low in the suspension resulting in a low center of gravity. It also allows manufactures to avoid tall spring mounts thus resulting in a flatter load floor about the suspension.[10] James Schefter reports that as used on the C5 and later Corvettes the use of OEM coilover damper springs would have forced the chassis engineers to either vertically raise the shock towers or move them inward. In the rear this would have reduced trunk space. In the front this would have interfered with engine packaging. The use of the leaf spring allowed the spring to be placed out of the way under the chassis and while keeping the diameter of the shock absorber assembly to that of just the damper rather than damper and spring.[12] However, in other applications such as race car designs, the need to span the width of the vehicle result in significant design limitations. Coil and torsion springs present better packaging options for racing applications. FRP springs also have limited availability and selection as compared to coil spring.[13] Higher cost has also been cited as a disadvantage when compared to coil springs on production road cars.[14]

Properties

FEA model of a leaf spring under load. The initial, unbent shape of the spring is shown as a silhouette box. An upward deflection on the right side of the spring results in a smaller upward movement on the left side.

A notable advantage of the FRP transverse leaf springs when supported with widely spaced, pivotable mounts is the ability to supplement or replace the anti-roll bar. Typically springs that provide a sufficient ride rate need a supplemental spring (the anti-roll bar) to increase the suspension roll rate. The coupling of the two sides of the transverse leaf spring across the vehicle results in an anti-roll bar like behavior. Corvette engineers have cited this property as enabling the use of a lighter anti-roll bar[9] and even eliminating the rear anti-roll bar on some versions of the seventh generation Corvette.[15]

When either wheel is deflected upward, the center span of the spring (the portion between the pivotable mounts) deflects downward. If both wheels deflect upward at the same time (displacing the suspension in bump) the center section bends uniformly between the pivot mounts. In roll only one wheel is deflected upwards. This tends to try to form the center of the spring into an "S" like curve. The result is the wheel rate of one side of the suspension depends on the displacement of the other side.[8][9][13] The extent to which the spring acts as an anti-roll bar depends on the distance between the pivot mounts and the rigidity of the pivot mounts.[8]

A transverse leaf spring with a central rigid mount. The two spring halves are effectively isolated. Movements of one half of the spring do not affect the other half.

A simplified flat, rectangular spring illustrates this principle. Deflecting the right side of the spring results in the left side rising. In comparison, a rigid central mount (2nd and 3rd generation Corvette and other cars) shows no movement on one side when the other is deflected.

Applications

A number of manufactures have produced vehicles or concepts utilizing independent front or rear suspensions supported by transverse leaf springs.

Recent patents and related research

Several automotive companies have researched suspension designs using a transverse composite leaf spring supported in a fashion similar to that of the Corvette.

See also

References

  1. ↑ https://books.google.de/books?id=WsjanO7xW58C&pg=PA81&lpg=PA81&dq=corvette+leaf+spring+design+history&source=bl&ots=CkRSGle9Qr&sig=BLRWxppsbVqjfRgdrRBqBmUbqns&hl=de&sa=X&ved=0ahUKEwjV0-3l7Z7MAhWhK5oKHcbfClU4FBDoAQgoMAI#v=onepage&q=corvette%20leaf%20spring%20design%20history&f=false
  2. ↑ http://www.corvetteonline.com/history-2/the-top-5-technological-advancements-in-corvette-history/
  3. ↑ http://www.edmunds.com/chevrolet/corvette/history/
  4. ↑ http://www.compositesworld.com/articles/composite-leaf-springs-saving-weight-in-production-suspension-systems
  5. ↑ http://www.autocomposites.org/composites101/history.cfm
  6. ↑ http://www.carbibles.com/suspension_bible.html
  7. ↑ Yu, W.J.; Kim, H.C. (1988). "Double tapered FRP beam for automotive suspension leaf spring". Composite Structures 9 (4): 279–300. doi:10.1016/0263-8223(88)90049-9.
  8. 1 2 3 4 Lamm, Michael (1983). The Newest Corvette. Corvette from A to Z-15 (1st ed.). Lamm-Morada Publishing. p. 44. ISBN 978-0932128041.
  9. 1 2 3 4 McLellan, Dave (2002). Corvette from the Inside. Cambridge, MA: Bentley Publishers. pp. 86–87. ISBN 0-8376-0859-7.
  10. 1 2 "Benteler-SGL mass-produces composite leaf springs for the new Volvo XC90 using Loctite Matrix resin from Henkel". Composites Industry News. FRP Today. Retrieved 2015-07-30.
  11. ↑ Knowles, Don (2010). Today's Technician: Automotive Suspension & Steering. Cengage Learning. p. 115.
  12. ↑ Schefter, James (1998). All Corvettes Are Red. Gallery Books. ISBN 978-0671685010.
  13. 1 2 Smith, Carroll (1984). Engineer to Win. Motorbooks. p. 207. ISBN 9780879381868. If I were involved in the design of a new passenger vehicle, however, I would give serious consideration to the use of a transverse composite single leaf spring of unidirectional glass or carbon filament in an epoxy matrix. This would be the lightest practical spring configuration and, although space constraints would seem to limit its use in racing, it should be perfectly feasible on road-going vehicles, from large trucks to small commuter cars. (Since I wrote this paragraph the new-generation Corvette has come out with just such a spring to control its independent suspension systems-at both end of the car.)
  14. ↑ Edmunds, Dan. "2014 Chevrolet Corvette Stingray Z51 Suspension Walkaround". Edmunds. Retrieved 2015-07-30.
  15. ↑ Noordeloos, Marc. "Vette Engineering Manager Explains the C7 Chassis". Automobile Magazine. Retrieved 2015-08-01.
  16. ↑ McCosh, Dan (April 1998). "Luxury coupes: $24,000 a seat". Popular Science. Retrieved 2015-07-30.
  17. ↑ Schuon, Marshal (Oct 23, 1994). "Behind the Wheel/1995 Volvo 960; A Box That's Well Rounded". The New York Times. Retrieved 2015-07-30.
  18. ↑ Stoklosa, Alexander. "10 Things You Need to Know About the 2016 Volvo XC90". Car and Driver. Retrieved 2015-08-01.
  19. ↑ Wood, Karen. "Composite leaf springs: Saving weight in production suspension systems". Composites World. Retrieved 2015-08-01.
  20. ↑ "The Smart Fortwo Evolution". Retrieved 2015-08-01.
  21. ↑ "Volkswagen : The 1-Litre Car". Automotive Intelligence News. Retrieved 2015-07-30.
  22. ↑ "The Successor: Indigo 3000" (PDF). Archived from the original (PDF) on 2008-12-16.
  23. ↑ "How it Works: Suspension". Unique Cars and Parts. Retrieved 2015-08-01.
  24. ↑ "Patent US7029017 – Wheel suspension for a motor vehicle with a transverse leaf spring". Google. Retrieved 2015-08-03.
  25. ↑ "Patent US6029987 – Front axle for a motor vehicle". Google. 1997-05-26. Retrieved 2015-08-03.
  26. ↑ "Patent US5141209 – Transverse leaf spring type suspension". Google. 1988-11-30. Retrieved 2015-08-03.
  27. ↑ "Patent US6811169 – Composite spring design that also performs the lower control arm function for a conventional or active suspension system". Google. Retrieved 2015-08-03.
  28. ↑ Plastic November 11th, 2009 admin (2009-11-11). "Plastic". That Car Blog. Retrieved 2015-08-03.
This article is issued from Wikipedia - version of the Friday, April 22, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.