EMD SD50

EMD SD50
Type and origin
Power type Diesel-electric
Builder GM Electro-Motive Division (EMD)
General Motors Diesel (GMD)
Clyde Engineering
Build date December 1980 – July 1987
Total produced 427
Specifications
Gauge 4 ft 8 12 in (1,435 mm) standard gauge
Length 71 ft 2 in (21.69 m) over the coupler pulling faces
Prime mover EMD 16-645F3B
Engine type V16 diesel
Alternator main : AR11
Cylinders 16
Performance figures
Power output 3,500 hp (2,610 kW) at 950 rpm; increased to 3,600 hp (2,685 kW) November 1984.
Career
Operators See Original buyers and Current owners
Disposition Many in service, many sold to regionals, dealers, or leasing companies as of 2008

The EMD SD50 is a 3,500-horsepower (2,610 kW) diesel-electric locomotive built by General Motors Electro-Motive Division. It was introduced in May 1981 as part of EMD's "50 Series", but prototype SD50S locomotives were built from 1980; production ceased in January 1986. The SD50 was in many respects a transitional model between EMD's Dash 2 series which was produced throughout the 1970s and the microprocessor-equipped SD60 and SD70 locomotives.

History

Norfolk Southern Loco No.5443 (EX-CR 6776 SD50).

The SD50 was produced in response to increasingly tough competition from GE Transportation Systems, whose Dash 7 line was proving quite successful with railroads. While EMD's SD40-2 was a reliable and trusted product, GE's line included locomotives up to 3,600 hp (2,685 kW) with more modern technology, as well as very competitive finance and maintenance deals. EMD responded throughout the SD50 program by offering discounts on large orders, this was also a response to the slow U.S. economy in the 1980s which cut locomotive orders.

GM-EMD had previously produced 3,600 hp (2,685 kW) locomotives, the SD45 and later SD45-2, but these used huge, 20-cylinder engines with high fuel consumption, and had reliability problems when first introduced. Demand for the 45 series dropped sharply after the 1970s fuel crises. The SD50 used an updated version of the V16 645 used in the SD40-2, uprated to 3,500 hp (2,600 kW)- and later 3,600 hp (2,685 kW) - at 950 rpm from 3,000 hp (2,240 kW) at 900 rpm. This proved to be a step too far; the 50 series models were plagued by engine and electrical system problems which harmed both sales and the reputation of EMD.

The subsequent SD60 model replaced the overstressed 950 rpm 645F engine with a new engine series, the 900 rpm 710G.

The SD50's long hood saw changes from previous EMD models. The overall frame length was increased, and the long hood was made substantially longer. The resistors for the dynamic brake grid were moved from their previous location above the prime mover to a new, cooler location in front of the engine compartment air intakes, where they were more effectively separated from the rest of the locomotives' systems, and also closer to the locomotive's electrical switchgear, thereby simplifying the prime mover maintenance procedures, and the electrical system as well.

Technical

The SD50 is powered by V16 16-645F3 series diesel engine driving either an EMD AR11A-D14 or an EMD AR16A-D18 traction alternator. The power generated by the traction alternator drove 6 EMD D87 traction motors rated at 1170 amps each.

Depending on customer options, the SD50 was available with a multitude of traction-motor gearing ratio and wheel size options, the most common of which being the 70:17 ratio with 40-inch (1,016 mm) wheels, this allowed for a top speed of 70 mph (110 km/h). Other gearing options for the SD50 with 40-inch (1,016 mm) wheels include 69:18 for 76 mph (122 km/h), 67:19 for 82 mph (132 km/h) and 66:20 for 88 mph (142 km/h). 42-inch (1,067 mm) wheels were also available. Customers of the SD50 also had the option of either HT-C trucks (identified with a hydraulic shock on the side of the middle axle of each truck) or the earlier Flexicoil trucks, which only Conrail opted for. Some investigators implicated the HT-C truck in derailments in Amtrak's SDP40F locomotive fleet and Conrail chose to order SD40-2s and their first order of SD50s with the earlier Flexicoil C truck. The controversy surrounding the HT-C truck was eventually disproved, and Conrail's second order of SD50s as well as their SD60 variants were all HT-C equipped.

The SD50 could be equipped with fuel tanks sizes from 3,200 US gallons (12,100 l; 2,660 imp gal) up to 4,400 US gallons (16,700 l; 3,660 imp gal), had a lube oil capacity of 396 US gallons (1,500 l; 330 imp gal) and a cooling water capacity of 276 US gallons (1,040 l; 230 imp gal).

SD50S

The SD50S ("short frame") were prototype units built in December 1980. They were shorter than production locomotives by approximately 2 feet (0.61 m). All of these prototypes were sold to the Norfolk & Western and passed to the Norfolk Southern; they were withdrawn in the early 2000s as non-standard. Two were rebuilt in 2008 as "SD40E" models by Norfolk Southern's Juniata Shops, along with several standard length SD50's.

The designation also applies to five locomotives built by EMD Australian licensee Clyde Engineering, Adelaide for Hamersley Iron. These were shorter than production SD50s, and were equipped with a special double cab roof for insulation against the hot Australian desert sun in the Pilbara region. Withdrawn in November 1995, they were sold to National Railway Equipment Company and exported to the U.S. in February 1999 and used in national lease service.[1] They were subsequently sold to the Utah Railway in June 2001, where they remain.[2]

SD50F

CN #5411 is an SD50F

The SD50F was a Canadian cowl unit version equipped with a "Draper taper" (inset section aft of cab for limited rear visibility). 60 were built for the Canadian National Railway as road numbers 5400-5459. Early engine problems resulted in a temporary down-rating to 3,300 horsepower (2,500 kW). Eventually the units were re-rated to 3,500 horsepower (2,600 kW); however, like their U.S. cousins, they continued to suffer from relatively low reliability, frequently suffering engine, power assembly, and crankshaft failures.

Out of the 60, only six of these locomotives are known to exist today, with the rest of the fleet scrapped.

Original buyers

Owner Quantity Numbers Notes
Baltimore and Ohio Railroad 20 8576-8595 to CSX Transportation, most have been rebuilt into SD50-2's. 14 rebuilt into SD50-3's.
Canadian National Railway 60 5400-5459 SD50F, Cowl units for CN only, retired, sold or scrapped. In 2008, CN retired the last of its SD50Fs, with most going to scrap or locomotive dealers. Dakota, Missouri Valley & Western picked up five of the units, with one now being used as a parts source. Two other units, 5404 and 5438, went via the shortline to Montana Limestone Co. at Warren, Mont.
Chicago and North Western Railway 35 7000-7034 to Union Pacific, retired. All were 3,600 hp.
Chesapeake and Ohio Railway 43 8553-8575, 8624-8643 to CSX Transportation, most have been rebuilt into SD50-2's. 14 rebuilt into SD50-3's. 8624-8643 were 3,600 hp.
Conrail 135 6700-6834 to CSX Transportation, Norfolk Southern Railway and Kansas City Southern, CSX-inherited units have been rebuilt into SD50-2's. 1 rebuilt to SD50-3 specs. Norfolk Southern inherited units have been rebuilt to SD40E's. 6780-6834 were 3,600 hp.
Denver and Rio Grande Western Railroad 17 5501-5517 to Southern Pacific, to Union Pacific, retired
Kansas City Southern Railway 10 704-713
Missouri Pacific Railroad 60 5000-5059 to Union Pacific, retired. All were 3,600 hp.
Norfolk and Western Railway 6 6500-6505 SD50S short frame to Norfolk Southern Railway, 6500-6501, 6503, 6505, scrapped. 6502, 6504 rebuilt into SD40E's.
Seaboard System Railroad 81 8500-8552, 8596-8623 to CSX Transportation, most have been rebuilt into SD50-2's. 14 rebuilt into SD50-3's. 8603-8623 were 3,600 hp.
Southern Railway 20 6506-6525 to Norfolk Southern Railway
Hamersley Iron 5 6060-6064 leased 1999 to Norfolk Southern Railroad, sold 2001 to Utah Railway[2]

Current owners

As of 2008, current owners and operators include:

Rebuilds

A number of SD50s have been rebuilt into the equivalent of SD40-2s. The Dash 2 features are already contained within the SD50. The units are re-rated from 3,500 hp (2,600 kW) at 950 rpm to 3,000 hp (2,200 kW) at 900 rpm. This is actually a quite simple change to the locomotive's Woodward PGE engine governor.

See also

Wikimedia Commons has media related to EMD SD50 locomotives.

References

  1. "Hammersley Loco Update" Railway Digest November 1998 pages 33, 36
  2. 1 2 Oberg, Leon (2010). Locomotives of Australia 1850s-2010s. Kenthurst: Rosenberg Publishing. pp. 390–391. ISBN 9781921719011.

External links

This article is issued from Wikipedia - version of the Thursday, April 21, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.