Floppy-disk controller

5 1/4 Diskette Drive Adapter found on the IBM PC (IBM 5150)

A floppy-disk controller (FDC) is a special-purpose chip and associated disk controller circuitry that directs and controls reading from and writing to a computer's floppy disk drive (FDD). This article contains concepts common to FDCs based on the NEC µPD765 and Intel 8272A or 82072A and their descendants, as used in the IBM PC and compatibles from the 1980s and 1990s. The concepts may or may not be applicable to, or illustrative of, other controllers or architectures.

Overview

A single floppy-disc controller (FDC) board can support up to four floppy disk drives. The controller is linked to the system bus of the computer and appears as a set of I/O ports to the CPU. It is often also connected to a channel of the DMA controller. On the x86 PC the floppy controller uses IRQ 6, on other systems other interrupt schemes may be used. The floppy disc controller usually performs data transmission in direct memory access (DMA) mode.

The diagram below shows a floppy disc controller which communicates with the CPU via an Industry Standard Architecture (ISA) bus. An alternative arrangement which is more usual in recent designs has the FDC included in a super I/O chip which communicates via a Low Pin Count (LPC) bus.

Most of the floppy disc controller (FDC) functions are performed by the integrated circuit but some are performed by external hardware circuits. The list of functions performed by each is given below.

Floppy disk controller functions (FDC)

External hardware functions

Input/output ports for common x86-PC controller

The FDC has three I/O ports. These are:

The first two reside inside the FDC IC while the Control port is in the external hardware. The addresses of these three ports are as follows.

Port Address
[hex]
Port Name Location Port type
3F5 Data register Bidirectional I/O
3F4 Main status register FDC IC Input
3F2 Digital control port External hardware Output

Data port

This port is used by the software for three different purposes:

Main status register (MSR)

This port is used by the software to read the overall status information regarding the FDC IC and the FDD's. Before initiating a floppy disk operation the software reads this port to confirm the readiness condition of the FDC and the disk drives to verify the status of the previously initiated command. The different bits of this register represent :

Bit Representation
0 FDD 0 : Busy in seek mode
1 FDD 1 : Busy in seek mode
2 FDD 2 : Busy in seek mode
3 FDD 3 : Busy in seek mode
4 FDC Busy; Read/Write command in progress
5 Non-DMA mode
6 DIO; Indicates the direction of data transfer between the FDC IC and the CPU
7 MQR; Indicates data register is ready for data transfer
Explanations
MQR 1 = data register ready, 0 = data register not ready
DIO 1 = controller has data for CPU, 0 = controller expecting data from CPU
Non-DMA 1 = Controller Not in DMA Mode, 0 = Controller in DMA Mode
FDC Busy 1 = Busy, 0 = Not Busy
FDD 0,1,2,3 1 = Running, 0 = Not Running

Digital control port

This port is used by the software to control certain FDD and FDC IC functions. The bit assignments of this port are:

Bit Representation
0 and 1 Device number to be selected
2 RESET FDC IC (Low)
3 Enable FDC interrupt and DMA request signals
4 to 7 Turn ON the motor in disk drive 0, 1, 2 or 3 respectively

Format data

Many mutually incompatible floppy disk formats are possible; aside from the physical format on the disk, incompatible file systems are also possible.

Drive Format Capacity Transfer
speed
[kbit/s]
RPM Tracks TPI Comment
8" SD 8" SD 80 KB 33.333 360 32 48 Only on old controllers.[1]
5.25" SD 5.25" SD 160 KB 125 40 Only on old controllers.
5.25" SD 5.25" SD 171 KB 250–308 300 35 48[2] Only on C1541 compatibles.
5.25" SD 5.25" SD 180 KB 150 40 Only on old controllers.
5.25" DD 5.25" DD 320/360/400 KB 250 300 40 48 .[3] 8/9/10 512K sectors respectively.
5.25" DD (96 tpi) 5.25" QD (2DD) 800 KB 250 300 80 96 [4]
5.25" HD 5.25" DD 360 KB 300 360 40 48 [5][6]
5.25" HD 5.25" HD 1200 KB 500 360 80 96 Up to 83 tracks. Different biasing current.[5][6]
5.25" HD 5.25" HD 720 KB 300 360 80 Up to 83 tracks.[3]
3.5" DD 3.5" DD 720 KB 250 300 80 135 Up to 83 tracks.[3][7]
3.5" DD 3.5" DD 800 KB 250 300 80 Used by C1581.
3.5" DD 3.5" DD 880 KB 250 300 80 Up to 83 tracks. Used by Amiga computers.
3.5" DD 3.5" DD 360 KB 250 300 40 [3]
3.5" HD 3.5" DD 720 KB 250 300 80 Up to 83 tracks.[3]
3.5" HD 3.5" HD 1440 KB 500 300 80 135 Up to 83 tracks.[3][8]
3.5" HD 3.5" HD 1760 KB 250 300 80 Used by Amiga computers.
3.5" ED 3.5" ED 2880 KB 1000 300 80 135 Up to 83 tracks.[7][9]

[10]

Sides:

Density:

"3mode" floppy drive

Primarily in Japan there are 3.5" high-density floppy drives that support three modes of disk formats instead of the normal two – 1440 KB (2 MB unformatted), 1.2 MB (1.6 MB unformatted) and 720 kB (1 MB unformatted). Originally, the high-density mode for 3.5" floppy drives in Japan only supported a capacity of 1.2 MB instead of the 1440 KB capacity that was used elsewhere.[11] While the more common 1440 KB format spun at 300 rpm, the 1.2 MB format instead spun at 360 rpm, thereby closely resembling the 1.2 MB format with 15 sectors per track previously found on 5.25" high-density floppy drives. Later Japanese floppy drives incorporated support for both high-density formats (as well as the single-density format), hence the name 3mode. Some BIOSes have a configuration setting to enable this mode for floppy drives supporting it.[12]

See also

References

External links

This article is issued from Wikipedia - version of the Sunday, April 24, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.