Magnetic flux

This article is about magnetic flux. For the magnetic fields "B" (magnetic flux density) and "H", see magnetic field.

In physics, specifically electromagnetism, the magnetic flux (often denoted Φ or ΦB) through a surface is the surface integral of the normal component of the magnetic field B passing through that surface. The SI unit of magnetic flux is the weber (Wb) (in derived units: volt-seconds), and the CGS unit is the maxwell. Magnetic flux is usually measured with a fluxmeter, which contains measuring coils and electronics, that evaluates the change of voltage in the measuring coils to calculate the magnetic flux.

Description

The magnetic flux through a surface—when the magnetic field is variable—relies on splitting the surface into small surface elements, over which the magnetic field can be considered to be locally constant. The total flux is then a formal summation of these surface elements (see surface integration).
Each point on a surface is associated with a direction, called the surface normal; the magnetic flux through a point is then the component of the magnetic field along this direction.

The magnetic interaction is described in terms of a vector field, where each point in space (and time) is associated with a vector that determines what force a moving charge would experience at that point (see Lorentz force). Since a vector field is quite difficult to visualize at first, in elementary physics one may instead visualize this field with field lines. The magnetic flux through some surface, in this simplified picture, is proportional to the number of field lines passing through that surface (in some contexts, the flux may be defined to be precisely the number of field lines passing through that surface; although technically misleading, this distinction is not important). Note that the magnetic flux is the net number of field lines passing through that surface; that is, the number passing through in one direction minus the number passing through in the other direction (see below for deciding in which direction the field lines carry a positive sign and in which they carry a negative sign). In more advanced physics, the field line analogy is dropped and the magnetic flux is properly defined as the surface integral of the normal component of the magnetic field passing through a surface. If the magnetic field is constant, the magnetic flux passing through a surface of vector area S is


\Phi_B = \mathbf{B} \cdot \mathbf{S} = BS \cos \theta,

where B is the magnitude of the magnetic field (the magnetic flux density) having the unit of Wb/m2 (tesla), S is the area of the surface, and θ is the angle between the magnetic field lines and the normal (perpendicular) to S. For a varying magnetic field, we first consider the magnetic flux through an infinitesimal area element dS, where we may consider the field to be constant:


d\Phi_B = \mathbf{B} \cdot d\mathbf{S}.

A generic surface, S, can then be broken into infinitesimal elements and the total magnetic flux through the surface is then the surface integral


\Phi_B = \iint\limits_S \mathbf{B} \cdot d\mathbf S.

From the definition of the magnetic vector potential A and the fundamental theorem of the curl the magnetic flux may also be defined as:

\Phi_B = \oint\limits_{\partial S} \mathbf{A} \cdot d\boldsymbol{\ell},

where the line integral is taken over the boundary of the surface S, which is denoted ∂S.

Magnetic flux through a closed surface

Some examples of closed surfaces (left) and open surfaces (right). Left: Surface of a sphere, surface of a torus, surface of a cube. Right: Disk surface, square surface, surface of a hemisphere. (The surface is blue, the boundary is red.)

Gauss's law for magnetism, which is one of the four Maxwell's equations, states that the total magnetic flux through a closed surface is equal to zero. (A "closed surface" is a surface that completely encloses a volume(s) with no holes.) This law is a consequence of the empirical observation that magnetic monopoles have never been found.

In other words, Gauss's law for magnetism is the statement:

\Phi_B=\,\!\oiint\scriptstyle S\mathbf{B} \cdot d\mathbf S = 0

for any closed surface S.

Magnetic flux through an open surface

For an open surface Σ, the electromotive force along the surface boundary, ∂Σ, is a combination of the boundary's motion, with velocity v, through a magnetic field B (illustrated by the generic F field in the diagram) and the induced electric field caused by the changing magnetic field.

While the magnetic flux through a closed surface is always zero, the magnetic flux through an open surface need not be zero and is an important quantity in electromagnetism. For example, a change in the magnetic flux passing through a loop of conductive wire will cause an electromotive force, and therefore an electric current, in the loop. The relationship is given by Faraday's law:

\mathcal{E} = \oint_{\partial \Sigma}\left(  \mathbf{E} +\mathbf{ v \times B}\right) \cdot d\boldsymbol{\ell} = -{d\Phi_B \over dt},

where

\mathcal{E} is the electromotive force (EMF),
ΦB is the magnetic flux through the open surface Σ,
∂Σ is the boundary of the open surface Σ; note that the surface, in general, may be in motion and deforming, and so is generally a function of time. The electromotive force is induced along this boundary.
d is an infinitesimal vector element of the contour ∂Σ,
v is the velocity of the boundary ∂Σ,
E is the electric field,
B is the magnetic field.

The two equations for the EMF are, firstly, the work per unit charge done against the Lorentz force in moving a test charge around the (possibly moving) surface boundary ∂Σ and, secondly, as the change of magnetic flux through the open surface Σ. This equation is the principle behind an electrical generator.

Area defined by an electric coil with three turns.

Comparison with electric flux

Main articles: Electric flux and Gauss's law

By way of contrast, Gauss's law for electric fields, another of Maxwell's equations, is

\Phi_E =\,\!\oiint\scriptstyle S\mathbf{E}\cdot d\mathbf{S} = \frac{Q}{\epsilon_0}\,\!

where

E is the electric field,
S is any closed surface,
Q is the total electric charge inside the surface S,
ε0 is the electric constant (a universal constant, also called the "permittivity of free space").

Note that the flux of E through a closed surface is not always zero; this indicates the presence of "electric monopoles", that is, free positive or negative charges.

See also

External articles

Patents
    This article is issued from Wikipedia - version of the Saturday, March 05, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.