Northrop YB-35

YB-35
YB-35 prototype
Role Strategic bomber
Manufacturer Northrop
Designer Jack Northrop
First flight 25 June 1946
Status Cancelled in 1949
Primary user United States Air Force
Program cost US$66 million[1]
Variants Northrop YB-49

The Northrop XB-35 and YB-35 were experimental heavy bomber aircraft developed by the Northrop Corporation for the United States Army Air Forces during and shortly after World War II. The airplane used the radical and potentially very efficient flying wing design, in which the tail section and fuselage are eliminated and all payload is carried in a thick wing. Only prototype and pre-production aircraft were built, although interest remained strong enough to warrant further development of the design as a jet bomber, under the designation YB-49.[2]

Design and development

The B-35 was the brainchild of Jack Northrop, who made the flying wing the focus of his work during the 1930s. During World War II, Northrop had been commissioned to develop a large wing-only, long-range bomber designated XB-35. Northrop advocated a "flying wing" as a means of reducing parasitic drag and eliminating structural weight not directly responsible for producing lift. In theory, the B-35 could carry a greater payload faster, farther, and cheaper than a conventional bomber. On 11 April 1941, the United States Army Air Corps sent out a request for a bomber that could carry 4,500 kg (10,000 lb) of bombs to a round-trip mission of 16,000 km (10,000 mi). Requested performance was a maximum speed of 720 km/h (450 mph), cruise speed of 443 km/h (275 mph), and service ceiling of 14,000 m (45,000 ft). This aircraft would be able to bomb Nazi-occupied Europe in the event that Britain fell. (This was similar to Nazi Germany's own Amerika Bomber program design competition through RLM, itself initiated in the spring of 1942.) The original April 1941 USAAC proposal was first submitted to Boeing and Consolidated Aircraft Company and led to the production of the Convair B-36. In May the contract was also extended to include Northrop, inviting them to submit a design along the lines they were already exploring.[2][3]

Since the new aircraft would require a significant amount of engineering work in untested waters, the first order placed was actually for a one-third scale version of the XB-35 dubbed the Northrop N-9M (M standing for model). This aircraft would be used to gather flight test data on the Flying Wing design, which would then be used in designing the big XB-35. It would also be used as a flight trainer, to familiarize pilots with the radical, all-wing concept. Early in 1942, design work on the XB-35 itself began in earnest. Unlike conventional aircraft, truly "tailless" flying wings cannot use a rudder for lateral control as it was absent, so a set of clamshell-like, double split flaps on the trailing edge of the wingtips were used. When aileron control was input, they were deflected up or down as a single unit, just like an aileron. When rudder input was made, the two surfaces on one side opened, top and bottom, creating drag, and yawing the aircraft. By applying input to both rudder pedals, both sets of surfaces were deployed creating drag so that the airspeed or the glide angle could be manipulated.[3]

Variants

XB-35

On 22 November 1941, the United States Army Air Forces (USAAF, or AAF) signed the development contract for an XB-35;[4] the contract included an option for a second aircraft, which was exercised on 2 January 1942. The first was to be delivered in November 1943, the second in April of the next year.

Detailed engineering began in early 1942. A fuselage-like crew cabin was to be embedded inside the wing; it included a tail cone protruding from the trailing edge. This tail cone would contain the remote sighting stations for the bomber's gunners and a cluster of rear-firing machine guns in the production aircraft. In the midsection of the cabin, there were folding bunks for off-duty crew on long missions.[5] The aircraft's bomb load was to be carried in six smaller bomb bays, three in each wing section, fitted with roll-away doors; this original design precluded the carrying of large bombs, and the early atomic bombs, without bomb bay redesign and modifications.[6][7] Production aircraft would have defensive armament of twenty 0.5 in (12.7 mm) machine guns or 20 mm cannon, carried in six turrets, two turrets along the aircraft's center line, four above and below the outer wings, and four in the "stinger" tail cone.[8] The B-35 would take advantage of a new aluminum alloy devised by Alcoa; it was considerably stronger than any alloy used previously.

In June 1946, the XB-35 made its first flight, a 45-minute trip from Hawthorne, California, to Muroc Dry Lake, without incident.[9] The XB-35's engines and propellers were AAF property, and had not been tested for engine-propeller compatibility by either Pratt & Whitney, Hamilton Standard, or by the AAF which bought them at Wright Field without testing them or assuring reliability, and then shipped them to Northrop. Microfilmed records of reports and correspondence of the XB-35 program relate that after three or four flights, power plant and propeller vibrations increased, and the very efficient contra-rotating propellers began failing with frustrating frequency. Meetings were called by Northrop, of the AAF, Pratt & Whitney and Hamilton Standard where no one would take responsibility for correcting the AAF's engines and propellers. In addition, the AAF failed to supply the AC electrical alternator, insisting on Northrop using an onboard auxiliary power unit (APU) unit driven by an automotive engine which limited the high-altitude, high-speed XB-35 to test flights below 15,000 ft (4,600 m). The AAF also refused to allow Northrop proposed modification of the bomb bays to carry the standard Mk. 3 atomic bomb, while at the same time declaring the AF would not buy the bomber unless it could carry the A-bomb. Northrop reluctantly agreed to try a single-rotation propeller, which slightly increased takeoff distance and a reduced rate-of-climb and maximum speed.

Problems with the quartet of contra-rotating propellers' shafts comprising each aircraft's drive-line system continued until finally Jack Northrop himself grounded the XB-35s until the government fixed their propulsion system. Concurrently, the AAF ordered Northrop to convert two of the YB-35 airframes to YB-49s, essentially substituting eight jet engines for four reciprocating engines. As a result, the airframe promptly flew to more than 40,000 ft (12,000 m) and topped 520 mph (840 km/h) in flight tests, verifying the XB-35 air frame's aerodynamics, but at the price of range. The prop-version had a design range capable of reaching targets 4,000 mi (6,400 km) away, but the jet-engine version's range was cut nearly in half. The new version disqualified it for the Air Force's top-priority mission as a strategic bomber, which at that time meant striking at the USSR's industrial and military complexes in the Ural Mountains.[10] The Air Force, itself involved in a confusion of rank and job changes, eventually cancelled the XB-35 project, while continuing testing the B-35 airframe as the YB-49, even ordering 30 of the jet-powered bombers after the first YB-49 crashed. The first and second XB-35s were scrapped on 23 and 19 August 1949, respectively.[11]

YB-35

On 30 September 1943, 13 pre-production YB-35s were ordered by the Army Air Force. The first one did not fly until 15 May 1948. While some Air Force generals felt the piston engines made the B-35 obsolete, it remained superior in overall performance and range to its competitor, the Convair B-36, and General Hoyt Vandenberg wrote that only the B-35 and the B-36 had adequate range for the Air Force's primary mission, and nothing comparable would be available until the mid-1950s.[10] Only the first YB-35 was ever flown. Multiple flight testing demonstrated that it was airworthy; it was then parked and ignored for more than a year until being scrapped on 20 July 1949. The unfinished YB-35 #2, was scrapped almost a month later, on 19 August 1949. The other 11 of 13 YB-35 aircraft ordered underwent conversion to other power plants.

YB-49

Two of those airframes were converted to use eight Allison J35 jet engines, and designated YB-49. The second YB-35 converted to a YB-49 all-jet airframe crashed after Air Force test pilot Forbes pulled the outer wing panels off during stall tests at 4.8 g0 (47 m/s2). The first YB-35 airframe jet-modified to a YB-49 completed all stall tests and even demonstrated recovery from a spin. It was later destroyed after the Flying Wing's forward landing gear strut and wheel collapsed after encountering high vibration during a highly unusual taxi test procedure made with the engine's fuel tanks full, causing a fire that spread rapidly.[10] Seven incomplete airframes began conversion to jet power as YB-35B but were never finished.

YRB-49A

A third YB-35 airframe was converted to use six jet engines (two placed in under wing pods) for use as a long-range reconnaissance aircraft, designated YRB-49A. After only a few months, the Air Force's order for 30 YRB-49As was suddenly cancelled without explanation. The sole YRB-49A built flew 13 test flights and then was returned to Northrop's Ontario Airport. The last of Northrop's big Flying Wings sat abandoned at the airport's edge for two years and was finally ordered scrapped on 1 December 1953.[12]

EB-35B

In order to test the advanced Northrop T37 Turbodyne turboprop engine, produced by a Northrop subsidiary, the final YB-35A was to be converted to a single EB-35B test aircraft (in this case the prefix "E" for the designation meant "Exempt," not the later Electronic). The test aircraft would use two of the powerful T37 engines, each driving a pair of contra-rotating, paddle-blade propellers; the first planned ground tests were to be made using a single T37 engine.[1] When the EB-35B project was canceled, the Air Force had Northrop's Turbodyne engine name, all its patents, and technical data reassigned to General Electric.[13]

B2T

The B2T was a U.S. Navy designation for one B-35B airframe to be used for development trials; the project was canceled while still in the planning stage.

Operational history

The U.S. Army Air Forces had originally ordered 200 production model B-35s. Since Northrop's facilities were not up to the task of producing them, the Glenn L. Martin Company agreed to undertake mass production. This proved irrelevant when the aircraft had too many development problems. Even disregarding these, so many of Martin's engineers had been drafted by 1944 that Martin pushed the first delivery date back to 1947. Seeing that it would almost certainly never be ready in time for the war, the Army Air Forces canceled the production contract, though the Air Technical Services Command continued to run the program for research purposes.

Actual flight tests of the aircraft revealed several problems: The contra-rotating props caused constant heavy drive-shaft vibration and the government-supplied gearboxes had frequent malfunctions and reduced the effectiveness of propeller control. After only 19 flights, Northrop grounded the first XB-35; the second aircraft was grounded after eight test flights. During this time, the contra-rotating propellers were removed and replaced with four-blade single-rotation propellers. In addition to having continued drive shaft vibration problems, the new single-rotation props greatly reduced the aircraft's speed and performance. Furthermore, the intricate exhaust system turned into a fiasco to maintain. After only two years of use, the engines already showed signs of metal fatigue.[12]

In the end, the program was terminated due to its technical difficulties, the obsolescence of its reciprocating propeller engines, and the program being far behind schedule and over budget. Another contributing factor to the program's failure was the tendency of Northrop to become engaged in many experimental programs, which spread its small engineering staff far too wide. While the competing propeller-driven B-36 was obsolete by that time and had just as many or even more development problems, the Air Force needed a very long-range, post-war atomic bomber to counter the perceived Soviet threat. It had more faith that the B-36's "teething" problems could be overcome, compared to those of the new and radical "Flying Wing", the unofficial name that was later associated with all the Northrop "all-wing" designs.

There are long-standing conspiracy theories about the cancellation of the Flying Wing program; specifically, an accusation from Jack Northrop that Secretary of the Air Force Stuart Symington attempted to coerce him to merge his company with the Atlas Corporation-controlled Convair. In a 1979 taped interview, Jack Northrop claimed the Flying Wing contract was cancelled because he would not agree to a merger because Convair's merger demands were "grossly unfair to Northrop." When Northrop refused, Symington supposedly arranged to cancel the B-35 and B-49 program. Symington became president of Convair after he left government service a short time later.[14]

Other observers note that the B-35 and B-49 designs had well-documented performance and design issues while the Convair B-36 needed more development money.[15] At that time, it appeared the B-36 program might be cancelled as well as the B-35. The USAF and the Texas Congressional delegation desired to have a production program for the large Fort Worth aircraft production factory, and Convair had much more effective lobbyists in Washington DC. The Northrop Corporation was always a technological trailblazer but the independent nature of Jack Northrop often collided with the political wheeling-and-dealing in Washington that tended to run huge military allocations. Consequently, the B-36 prevailed, with just over 380 aircraft built. Furthermore, earlier the same year, when the YB-49 jet bomber was cancelled, Northrop received a smaller production contract for its F-89 Scorpion fighter as compensation for the lost Flying Wing contract.[16][17]

Specifications (YB-35)

General characteristics

Fuselage diameter: 9 ft 6 in (2.9 m)

Performance

Armament

See also

Related development
Aircraft of comparable role, configuration and era
Related lists

References

Notes

  1. 1 2 Knaack 1988, p. 506.
  2. 1 2 Parker, Dana T. Building Victory: Aircraft Manufacturing in the Los Angeles Area in World War II, pp. 93, 95, 103-6, Cypress, CA, 2013. ISBN 978-0-9897906-0-4.
  3. 1 2 Winchester 2005, p. 193.
  4. Allen 2003, p.5
  5. Allen 2003, pp. 6–7.
  6. Flight 20 March 1947, p. a.
  7. Allen 2003, p. 8.
  8. Gunston 1996, p. 33.
  9. Swopes, Bryan R. "25 June 1946". thisdayinaviation.com. Retrieved 26 June 2014.
  10. 1 2 3 "US government microfilm A2061, XB-35 Project Report, Vols. 1–4", Air Force Case History Files. Retrieved: 29 January 2011.
  11. "USAF Museum XB-35 fact sheet", nationalmuseum.af.mil. Retrieved: 4 January 2010.
  12. 1 2 Winchester 2005, p. 192.
  13. Wooldridge, E.T. "The Northrop Bombers." Century of Flight, 2003. Retrieved: 27 August 2011.
  14. Fitzsimons 1978, p. 2282.
  15. Donald 1997, p. 709.
  16. Donald 1997, p. 708.
  17. Jones 1975, p. 238.

Bibliography

  • Allen, Francis. "Before the B-2: Northrop's Flying Wings, The XB-35 and XB-49". Air Enthusiast. No. 106, July/August 2003, pp. 2–12. Stamford, UK: Key Publishing. ISSN 0143-5450.
  • Coleman, Ted. Jack Northrop and the Flying Wing: The Real Story Behind the Stealth Bomber. New York: Paragon House, 1988. ISBN 1-55778-079-X.
  • Donald, David, ed. "Northrop Flying Wings". Encyclopedia of World Aircraft. Etobicoke, Ontario: Prospero Books, 1997. ISBN 1-85605-375-X.
  • Fitzsimons, Bernard, ed. "Scorpion, Northrop F-89." Illustrated Encyclopedia of 20th Century Weapons and Warfare, Volume 21. London: Phoebus, 1978. ISBN 0-8393-6175-0.
  • Gunston, Bill. "Northrop's Flying Wings". Wings of Fame. Volume 2, pp. 24–37. London: Aerospace Publishing, 1996. ISBN 1-874023-69-7. ISSN 1361-2034.
  • Jones, Lloyd S. U. S. Fighters. Fallbrook, California: Aero Publishers, 1975. ISBN 0-8168-9200-8.
  • Knaack, Marcelle Size. Post-World War II Bombers, 1945–1973. Washington, D.C.: Office of Air Force History, 1988. ISBN 0-16-002260-6.
  • Maloney, Edward T. Northrop Flying Wings, Corona del Mar, California: World War II Publications, 1988. ISBN 0-915464-00-4.
  • O'Leary, Michael. "Wings of Northrop, Part Three." Air Classics, Volume 44, Number 2, February 2008, Challenge Publications, Inc. ISSN 0002-2241. (Heavily illustrated, authoritative XB/YB-35 article.)
  • Pape, Garry and John Campbell. Northrop Flying Wings: A History of Jack Northrop's Visionary Aircraft. Atglen, Pennsylvania: Schiffer Publishing, Ltd., 1995. ISBN 0-88740-689-0.
  • Winchester, Jim, "Northrop XB-35/YB-49". Concept Aircraft: Prototypes, X-Planes and Experimental Aircraft. Kent, UK: Grange Books plc., 2005. ISBN 978-1-84013-809-2.
  • "The Wing". Flight, 20 March 1947, pp. a–b, 241.
  • Wooldridge, E. T. Winged Wonders: The Story of the Flying Wings. Washington, D.C.: Smithsonian Institution Press, 1983. ISBN 0-87474-966-2.

External links

Wikimedia Commons has media related to Northrop XB-35.
This article is issued from Wikipedia - version of the Friday, January 22, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.