Pneumatic valve springs

Pneumatic valve springs are metal bellows filled with compressed air^[1] used as an alternative to the metal wire springs used to close valves in high-speed internal combustion engines. This system was introduced in the mid-1980s in Renault turbocharged 1.5 litre Formula One engines.

Concept

Racing engines often fail at high rotational speeds because mechanical springs are unable to retract the valves quickly enough to provide clearance for the piston. Renault's pneumatic valve technology replaced steel springs with light weight compressed air bellows. These could retract valves more quickly and reduce the possibility of piston-valve interference, as long as pressure could be maintained. Additionally, the amount of seat tension required to keep a coil sprung valve under control results in greater peak lift loading, with added stress to the entire valvetrain as a result. Pneumatic systems, sharing a common reservoir of pressure retain a more static level of force, controlling the valve effectively, without any attendant peak lift load increase.

The actuation mechanism is simply a piston and cylinder, similar to a small pneumatic ram. The tappet bore where a hydraulic tappet would normally reside, becomes the cylinder, and the retainer assembly becomes the piston. Pressurized air (nitrogen) is pumped into this cylinder which then causes the piston/retainer to rise to the top of cylinder, causing the valve to form an airtight seal with the seat. The compressed gas then becomes the spring so to speak, and does not have the same traits as springs do at elevated rpm. A small light spring is sometimes fitted between the piston and retainer so that when the system is switched off the spring forces the piston down against the bottom of bore and thus forces the retainer upwards. This ensures that no crown-to-valve contact occurs when shut down.

Pneumatic valve technology in racing

Pneumatic valve springs gave Renault an advantage with its turbocharged engines, often said to be one of the most powerful. However, reliability and poor handling of their chassis kept the cars from success until 1989 when Renault provided Williams with a new V10 engine to begin a winning streak.

Pneumatic valve springs are also found in several Moto GP motorcycle engines, debuting in 2002 with the Aprilia RS Cube. In 2005, Team Roberts was the first to use pneumatic valves full-time in their uncompetitive KTM powered bike. Today, almost all of the MotoGP teams use pneumatic valve technology on their bikes, including Yamaha, Suzuki and Honda. Ducati uses a desmodromic design.

Future valve technology

While pneumatic valve springs have become standard in Formula One engines, Renault has been researching computer-controlled electromagnetic valve actuation (EVA) using no camshaft, to reduce moving parts while improving valve control.

Notes

↑ Scarborough, Craig, F1 Engines _ Valve technology, retrieved 2007-03-05

^[1]

Automotive engine

Part of the Automobile series

Basic terminology	Compression ratio Crank Cylinder Dead centre Diesel engine Dry sump Engine balance Engine configuration Engine displacement Engine knocking Firing order Hydrolock Petrol engine Power band Redline Spark-ignition engine Stroke Stroke ratio Wet sump

Main components	Connecting rod Crankcase Crankpin Crankshaft Crossflow cylinder head Crossplane Cylinder bank Cylinder block Cylinder head Flywheel Head gasket Hypereutectic piston Main bearing Piston Piston ring Reverse-flow cylinder head Starter ring gear Sump

Valvetrain	Cam Cam follower Camshaft Desmodromic valve Hydraulic tappet Multi-valve Overhead camshaft Overhead valve Pneumatic valve springs Poppet valve Pushrod Rocker arm Sleeve valve Tappet Timing belt Timing mark Valve float Variable valve timing

Aspiration	Air filter Blowoff valve Boost controller Butterfly valve Centrifugal-type supercharger Cold air intake Dump valve Electronic throttle control Forced induction Inlet manifold Intake Intercooler Manifold vacuum Naturally aspirated engine Ram-air intake Scroll-type supercharger Short ram air intake Supercharger Throttle Throttle body Turbocharger Twin-turbo Variable-geometry turbocharger Variable-length intake manifold Warm air intake

Fuel system	Carburetor Common rail Direct injection Fuel filter Fuel injection Fuel pump Fuel tank Gasoline direct injection Indirect injection Injection pump Lean-burn Stratified charge engine Turbo fuel stratified injection Unit injector

Ignition	Contact breaker Magneto Distributor Electrical ballast High tension leads Ignition coil Spark plug Wasted spark

Electrics and engine management	Air–fuel ratio meter Alternator Automatic Performance Control Car battery (lead–acid battery) Crankshaft position sensor Dynamo Drive by wire Electronic control unit Engine control unit Engine coolant temperature sensor Glow plug Idle air control actuator MAP sensor Mass flow sensor Oxygen sensor Starter motor Throttle position sensor

Exhaust system	Automobile emissions control Catalytic converter Diesel particulate filter Exhaust manifold Glasspack Muffler

Engine cooling	Air cooling Antifreeze (ethylene glycol) Core plug Electric fan Fan belt Radiator Thermostat Water cooling Viscous fan (fan clutch)

Other components	Balance shaft Block heater Combustion chamber Cylinder head porting Gasket Motor oil Oil filter Oil pump Oil sludge PCV valve Seal Synthetic oil Underdrive pulleys

Portal Category

↑ http://www.f1technical.net/forum/viewtopic.php?t=15385

This article is issued from Wikipedia - version of the Monday, October 26, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.

Pneumatic valve springs

Concept

Pneumatic valve technology in racing

Future valve technology

Notes

Further reading

See also