Rheology

Rheology (/riːˈɒlədʒi/; from Greek ῥέω rhéō, "flow" and -λoγία, -logia, "study of") is the study of the flow of matter, primarily in a liquid state, but also as 'soft solids' or solids under conditions in which they respond with plastic flow rather than deforming elastically in response to an applied force.[1] It applies to substances which have a complex microstructure, such as muds, sludges, suspensions, polymers and other glass formers (e.g., silicates), as well as many foods and additives, bodily fluids (e.g., blood) and other biological materials or other materials which belong to the class of soft matter.

Newtonian fluids can be characterized by a single coefficient of viscosity for a specific temperature. Although this viscosity will change with temperature, it does not change with the strain rate. Only a small group of fluids exhibit such constant viscosity. The large class of fluids whose viscosity changes with the strain rate (the relative flow velocity) are called non-Newtonian fluids.

Rheology generally accounts for the behavior of non-Newtonian fluids, by characterizing the minimum number of functions that are needed to relate stresses with rate of change of strain or strain rates. For example, ketchup can have its viscosity reduced by shaking (or other forms of mechanical agitation, where the relative movement of different layers in the material actually causes the reduction in viscosity) but water cannot. Ketchup is a shear thinning material, like yoghurt and emulsion paint (US terminology latex paint or acrylic paint), exhibiting thixotropy, where an increase in relative flow velocity will cause a reduction in viscosity, for example, by stirring. Some other non-Newtonian materials show the opposite behavior, rheopecty: viscosity going up with relative deformation, and are called shear thickening or dilatant materials. Since Sir Isaac Newton originated the concept of viscosity, the study of liquids with strain rate dependent viscosity is also often called Non-Newtonian fluid mechanics.[1]

The term rheology was coined by Eugene C. Bingham, a professor at Lafayette College, in 1920, from a suggestion by a colleague, Markus Reiner.[2][3] The term was inspired by the aphorism of Simplicius (often attributed to Heraclitus), panta rhei, "everything flows"[4][5]

The experimental characterization of a material's rheological behaviour is known as rheometry, although the term rheology is frequently used synonymously with rheometry, particularly by experimentalists. Theoretical aspects of rheology are the relation of the flow/deformation behaviour of material and its internal structure (e.g., the orientation and elongation of polymer molecules), and the flow/deformation behaviour of materials that cannot be described by classical fluid mechanics or elasticity.

Scope

In practice, rheology is principally concerned with extending continuum mechanics to characterize flow of materials, that exhibits a combination of elastic, viscous and plastic behavior by properly combining elasticity and (Newtonian) fluid mechanics. It is also concerned with establishing predictions for mechanical behavior (on the continuum mechanical scale) based on the micro- or nanostructure of the material, e.g. the molecular size and architecture of polymers in solution or the particle size distribution in a solid suspension. Materials with the characteristics of a fluid will flow when subjected to a stress which is defined as the force per area. There are different sorts of stress (e.g. shear, torsional, etc.) and materials can respond differently for different stresses. Much of theoretical rheology is concerned with associating external forces and torques with internal stresses and internal strain gradients and flow velocities.[1][6][7][8]

Continuum mechanics
The study of the physics of continuous materials		 Solid mechanics
The study of the physics of continuous materials with a defined rest shape.		 Elasticity
Describes materials that return to their rest shape after applied stresses are removed.
Plasticity
Describes materials that permanently deform after a sufficient applied stress.		 Rheology
The study of materials with both solid and fluid characteristics.
Fluid mechanics
The study of the physics of continuous materials which deform when subjected to a force.		 Non-Newtonian fluids do not undergo strain rates proportional to the applied shear stress.
Newtonian fluids undergo strain rates proportional to the applied shear stress.

Rheology unites the seemingly unrelated fields of plasticity and non-Newtonian fluid dynamics by recognizing that materials undergoing these types of deformation are unable to support a stress (particularly a shear stress, since it is easier to analyze shear deformation) in static equilibrium. In this sense, a solid undergoing plastic deformation is a fluid, although no viscosity coefficient is associated with this flow. Granular rheology refers to the continuum mechanical description of granular materials.

One of the major tasks of rheology is to empirically establish the relationships between deformations (or rates of deformation) and stresses, by adequate measurements, although a number of theoretical developments (such as assuring frame invariants) are also required before using the empirical data. These experimental techniques are known as rheometry and are concerned with the determination with well-defined rheological material functions. Such relationships are then amenable to mathematical treatment by the established methods of continuum mechanics.

The characterization of flow or deformation originating from a simple shear stress field is called shear rheometry (or shear rheology). The study of extensional flows is called extensional rheology. Shear flows are much easier to study and thus much more experimental data are available for shear flows than for extensional flows.

Rheologist

A rheologist is an interdisciplinary scientist or engineer who studies the flow of complex liquids or the deformation of soft solids. It is not a primary degree subject; there is no qualification of rheologist as such. Most rheologists have a qualification in mathematics, the physical sciences (e.g. chemistry, physics, biology), engineering (e.g. mechanical, chemical, materials science and engineering or civil engineering), medicine, or certain technologies, notably materials or food. Typically, a small amount of rheology may be studied when obtaining a degree, but a person working in rheology will extend this knowledge during postgraduate research or by attending short courses and by joining a professional association (see below).

Viscoelasticity

Main article: Viscoelasticity

Applications

Rheology has applications in materials science engineering, geophysics, physiology, human biology and pharmaceutics. Materials science is utilized in the production of many industrially important substances, such as cement, paint, and chocolate, which have complex flow characteristics. In addition, plasticity theory has been similarly important for the design of metal forming processes. The science of rheology and the characterization of viscoelastic properties in the production and use of polymeric materials has been critical for the production of many products for use in both the industrial and military sectors. Study of flow properties of liquids is important for pharmacists working in the manufacture of several dosage forms, such as simple liquids, ointments, creams, pastes etc. The flow behavior of liquids under applied stress is of great relevance in the field of pharmacy. Flow properties are used as important quality control tools to maintain the superiority of the product and reduce batch to batch variations.

Materials science

Polymers

Examples may be given to illustrate the potential applications of these principles to practical problems in the processing[10] and use of rubbers, plastics, and fibers. Polymers constitute the basic materials of the rubber and plastic industries and are of vital importance to the textile, petroleum, automobile, paper, and pharmaceutical industries. Their viscoelastic properties determine the mechanical performance of the final products of these industries, and also the success of processing methods at intermediate stages of production.

In viscoelastic materials, such as most polymers and plastics, the presence of liquid-like behaviour depends on the properties of and so varies with rate of applied load, i.e., how quickly a force is applied. The silicone toy 'Silly Putty' behaves quite differently depending on the time rate of applying a force. Pull on it slowly and it exhibits continuous flow, similar to that evidenced in a highly viscous liquid. Alternatively, when hit hard and directly, it shatters like a silicate glass.

In addition, conventional rubber undergoes a glass transition, (often called a rubber-glass transition). E.G. The Space Shuttle Challenger disaster was caused by rubber O-rings that were being used well below their glass transition temperature on an unusually cold Florida morning, and thus could not flex adequately to form proper seals between sections of the two solid-fuel rocket boosters.

Biopolymers

Linear structure of cellulose -- the most common component of all organic plant life on Earth. * Note the evidence of hydrogen bonding which increases the viscosity at any temperature and pressure. This is an effect similar to that of polymer crosslinking, but less pronounced.

Sol-gel

Main article: sol-gel
Polymerization process of tetraethylorthosilicate (TEOS) and water to form amorphous hydrated silica particles (Si-OH) can be monitored rheologically by a number of different methods.

With the viscosity of a sol adjusted into a proper range, both optical quality glass fiber and refractory ceramic fiber can be drawn which are used for fiber optic sensors and thermal insulation, respectively. The mechanisms of hydrolysis and condensation, and the rheological factors that bias the structure toward linear or branched structures are the most critical issues of sol-gel science and technology.

Geophysics

Geophysics includes the flow of molten lava and debris flows (fluid mudslides). Also included in this disciplinary branch are solid Earth materials which only exhibit flow over extended time scales. Those that display viscous behaviour are known as rheids. E.G. granite can flow plastically with a negligible yield stress at room temperatures, (i.e. a viscous flow). Long term creep experiments (~ 10 years) indicate that the viscosity of granite and glass under ambient conditions are on the order of 1020 poises.[11][12]

Physiology

Physiology includes the study of many bodily fluids that have complex structure and composition, and thus exhibit a wide range of viscoelastic flow characteristics. In particular there is a specialist study of blood flow called hemorheology. This is the study of flow properties of blood and its elements (plasma and formed elements, including red blood cells, white blood cells and platelets). Blood viscosity is determined by plasma viscosity, hematocrit (volume fraction of red blood cell, which constitute 99.9% of the cellular elements) and mechanical behaviour of red blood cells. Therefore, red blood cell mechanics is the major determinant of flow properties of blood.[13]

Food rheology

Food rheology is important in the manufacture and processing of food products, e.g. cheese.[14]

Thickening agents, or thickeners, are substances which, when added to an aqueous mixture, increase its viscosity without substantially modifying its other properties, such as taste. They provide body, increase stability, and improve suspension of added ingredients. Thickening agents are often used as food additives and in cosmetics and personal hygiene products. Some thickening agents are gelling agents, forming a gel. The agents are materials used to thicken and stabilize liquid solutions, emulsions, and suspensions. They dissolve in the liquid phase as a colloid mixture that forms a weakly cohesive internal structure. Food thickeners frequently are based on either polysaccharides (starches, vegetable gums, and pectin), or proteins.[15][16]

Concrete rheology

Concrete's and mortar's workability is related to the rheological properties of the fresh cement paste. The mechanical properties of hardened concrete increase if less water is used in the concrete mix design, however reducing the water-to-cement ratio may decrease the ease of mixing and application. To avoid these undesired effects, superplasticizers are typically added to decrease the apparent yield stress and the viscosity of the fresh paste. Their addition highly improves concrete and mortar properties.[17]

Filled polymer rheology

The incorporation of various types of fillers into polymers is a common means of reducing cost and to impart certain desirable mechanical, thermal, electrical and magnetic properties to the resulting material. The advantages that filled polymer systems have to offer come with an increased complexity in the rheological behavior.[18]

Usually when the use of fillers is considered, a compromise has to be made between the improved mechanical properties in the solid state on one side and the increased difficulty in melt processing, the problem of achieving uniform dispersion of the filler in the polymer matrix and the economics of the process due to the added step of compounding on the other. The rheological properties of filled polymers are determined not only by the type and amount of filler, but also by the shape, size and size distribution of its particles. An additional factor is the stress transfer at the filler-polymer interface. The interfacial adhesion can be substantially enhanced via a coupling agent that adheres well to both the polymer and the filler particles. The type and amount of surface treatment on the filler are thus additional parameters affecting the rheological and material properties of filled polymeric systems.

Measurement

Rheometers are instruments used to characterize the rheological properties of materials, typically fluids that are melts or solution. These instruments impose a specific stress field or deformation to the fluid, and monitor the resultant deformation or stress. Instruments can be run in steady flow or oscillatory flow, in both shear and extension.

Dimensionless numbers

Deborah number

Main article: Deborah number

On one end of the spectrum we have an inviscid or a simple Newtonian fluid and on the other end, a rigid solid; thus the behaviour of all materials fall somewhere in between these two ends. The difference in material behaviour is characterized by the level and nature of elasticity present in the material when it deforms, which takes the material behaviour to the non-Newtonian regime. The non-dimensional Deborah number is designed to account for the degree of non-Newtonian behaviour in a flow. The Deborah number is defined as the ratio of the characteristic time of relaxation (which purely depends on the material and other conditions like the temperature) to the characteristic time of experiment or observation.[3][19] Small Deborah numbers represent Newtonian flow, while non-Newtonian (with both viscous and elastic effects present) behaviour occurs for intermediate range Deborah numbers, and high Deborah numbers indicate an elastic/rigid solid. Since Deborah number is a relative quantity, the numerator or the denominator can alter the number. A very small Deborah number can be obtained for a fluid with extremely small relaxation time or a very large experimental time, for example.


Reynolds number

Main article: Reynolds number

In fluid mechanics, the Reynolds number is a measure of the ratio of inertial forces (vsρ) to viscous forces (μ/L) and consequently it quantifies the relative importance of these two types of effect for given flow conditions. Under low Reynolds numbers viscous effects dominate and the flow is laminar, whereas at high Reynolds numbers inertia predominates and the flow may be turbulent. However, since rheology is concerned with fluids which do not have a fixed viscosity, but one which can vary with flow and time, calculation of the Reynolds number can be complicated.

It is one of the most important dimensionless numbers in fluid dynamics and is used, usually along with other dimensionless numbers, to provide a criterion for determining dynamic similitude. When two geometrically similar flow patterns, in perhaps different fluids with possibly different flow rates, have the same values for the relevant dimensionless numbers, they are said to be dynamically similar.

Typically it is given as follows:

\mathit{Re} = {\rho u_{s}^2/L \over \mu u_{s}/L^2} = {\rho u_{s} L\over \mu} = {u_{s} L\over \nu}

where:

See also

References

  1. 1 2 3 W. R. Schowalter (1978) Mechanics of Non-Newtonian Fluids Pergamon ISBN 0-08-021778-8
  2. ↑ James Freeman Steffe (1 January 1996). Rheological Methods in Food Process Engineering. Freeman Press. ISBN 978-0-9632036-1-8.
  3. 1 2 The Deborah Number
  4. ↑ Barnes, Jonathan (1982). The presocratic philosophers. ISBN 978-0-415-05079-1.
  5. ↑ Beris, A. N.; Giacomin, A. J. (2014). "πάντα ῥεῖ : Everything Flows". Applied Rheology 24: 52918. doi:10.3933/ApplRheol-24-52918.
  6. ↑ R. B. Bird, W. E. Stewart, E. N. Lightfoot (1960), Transport Phenomena, John Wiley & Sons, ISBN 0-471-07392-X
  7. ↑ R. Byrin Bird, Charles F. Curtiss, Robert C. Armstrong (1989), Dynamics of Polymeric Liquids, Vol 1 &2 , Wiley Interscience, ISBN 0-471-51844-1 and 978-0471518440
  8. ↑ Faith A. Morrison (2001), Understanding Rheology, Oxford University Press, ISBN 0-19-514166-0 and 978-0195141665
  9. ↑ William N. Findley, James S. Lai, Kasif Onaran (1989), Creep and Relaxation of Nonlinear Viscoelastic Materials, Dover Publications
  10. ↑ A. V. Shenoy and D. R. Saini (1996), Thermoplastic Melt Rheology and Processing, Marcel Dekker Inc., New York.
  11. ↑ Kumagai, N., Sasajima, S., Ito, H., Long-term Creep of Rocks, J. Soc. Mat. Sci. (Japan), Vol. 27, p. 157 (1978) Online
  12. ↑ Vannoni, M.; Sordoni, A.; Molesini, G. (2011). "Relaxation time and viscosity of fused silica glass at room temperature". Eur. Phys. J. E 34 (9): 9–14. doi:10.1140/epje/i2011-11092-9.
  13. ↑ The ocular Vitreous humor is subject to rheologic observations, particularly during studies of age-related vitreous liquefaction, or synaeresis. Baskurt OK, Meiselman HJ; Meiselman (2003). "Blood rheology and hemodynamics". Seminars in Thrombosis and Haemostasis 29 (5): 435–450. doi:10.1055/s-2003-44551. PMID 14631543.
  14. ↑ S. Gunasekaran, M. Mehmet (2003), Cheese rheology and texture, CRC Press, ISBN 1-58716-021-8
  15. ↑ B.M. McKenna, and J.G. Lyng (2003). Texture in food – Introduction to food rheology and its measurement. ISBN 978-1-85573-673-3. Retrieved 2009-09-18.
  16. ↑ Nikolaev L.K., Nikolaev B.L., "EXPERIMENTAL STUDY OF RHEOLOGICAL CHARACTERISTICS OF MELTED CHEESE «MILK»", Processes and equipment for food production, Number 4(18), 2013
  17. ↑ Ferrari, L; Kaufmann, J; Winnefeld, F; Plank, J (2011). "Multi-method approach to study influence of superplasticizers on cement suspensions". Cement and Concrete Research 41 (10): 1058. doi:10.1016/j.cemconres.2011.06.010.
  18. ↑ Aroon V. Shenoy (1999), Rheology of Filled Polymer Systems, Kluwer Academic Publishers, Netherlands.
  19. ↑ Reiner, M. (1964). "The Deborah Number". Physics Today 17 (1): 62. doi:10.1063/1.3051374. ISSN 0031-9228.

External links

This article is issued from Wikipedia - version of the Thursday, March 17, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.