Rocker arm

A rocker arm (in the context of an internal combustion engine of automotive, marine, motorcycle and reciprocating aviation types) is an oscillating lever that conveys radial movement from the cam lobe into linear movement at the poppet valve to open it. One end is raised and lowered by a rotating lobe of the camshaft (either directly or via a tappet (lifter) and pushrod) while the other end acts on the valve stem. When the camshaft lobe raises the outside of the arm, the inside presses down on the valve stem, opening the valve. When the outside of the arm is permitted to return due to the camshafts rotation, the inside rises, allowing the valve spring to close the valve.

Overview

The drive cam is driven by the camshaft. This pushes the rocker arm up and down about the trunnion pin or rocker shaft. Friction may be reduced at the point of contact with the valve stem by a roller cam follower. A similar arrangement transfers the motion via another roller cam follower to a second rocker arm. This rotates about the rocker shaft, and transfers the motion via a tappet to the poppet valve. In this case this opens the intake valve to the cylinder head.

Leverage

The effective leverage of the arm (and thus the force it can exert on the valve stem) is determined by the rocker arm ratio, the ratio of the distance from the rocker arm's center of rotation to the tip divided by the distance from the center of rotation to the point acted on by the camshaft or pushrod. Current automotive design favors rocker arm ratios of about 1.5:1 to 1.8:1. However, in the past smaller positive ratios (the valve lift is greater than the cam lift) and even negative ratios (valve lift smaller than the cam lift) have been used. Many pre-World War II engines use a 1:1 (neutral) ratio.

Materials

For car engines the rocker arms are generally steel stampings, providing a reasonable balance of strength, weight and economical cost. Because the rocker arms are, in part, reciprocating weight, excessive mass especially at the lever ends limits the engine's ability to reach high operating speeds. Truck engines (mostly diesel) use stronger and stiffer rocker arms made of cast iron (usually ductile), or forged carbon steel.

History

Dating back to the 19th century, rocker arms have been made with and without roller tips that press upon the valve.

Use of alloys

Many lightweight and high strength alloys, and bearing configurations for the fulcrum, have been used in an effort to increase the RPM limits for high performance applications, eventually lending the benefits of these race bred technologies to more high-end production vehicles.

Geometry

Even the design aspects of the rocker arm's geometry has been studied and changed to maximize the cam information exchange to the valve which the rocker arm imposes, as set forth by the Miller US Patent, #4,365,785, issued to James Miller on December 28, 1982, often referred to as the MID-LIFT Patent. Previously, the specific pivot points with rocker arm design was based on older and less efficient theories of over-arcing motion which increased wear on valve tips, valve guides and other valve train components, besides diluting the effective cam lobe information as it was transferred through the rocker arm's motion to the valve. Jim Miller's MID-LIFT Patent set a new standard of rocker arm geometrical precision which defined and duplicated each engine's specific push-rod to valve attack angles, then designing the rocker's pivot points so that an exact perpendicular relationship on both sides of the rocker arm was attained: with the valve and the pushrod, when the valve was at its "mid-lift" point of motion.

References

Automotive engine

Part of the Automobile series

Basic terminology	Compression ratio Crank Cylinder Dead centre Diesel engine Dry sump Engine balance Engine configuration Engine displacement Engine knocking Firing order Hydrolock Petrol engine Power band Redline Spark-ignition engine Stroke Stroke ratio Wet sump

Main components	Connecting rod Crankcase Crankpin Crankshaft Crossflow cylinder head Crossplane Cylinder bank Cylinder block Cylinder head Flywheel Head gasket Hypereutectic piston Main bearing Piston Piston ring Reverse-flow cylinder head Starter ring gear Sump

Valvetrain	Cam Cam follower Camshaft Desmodromic valve Hydraulic tappet Multi-valve Overhead camshaft Overhead valve Pneumatic valve springs Poppet valve Pushrod Rocker arm Sleeve valve Tappet Timing belt Timing mark Valve float Variable valve timing

Aspiration	Air filter Blowoff valve Boost controller Butterfly valve Centrifugal-type supercharger Cold air intake Dump valve Electronic throttle control Forced induction Inlet manifold Intake Intercooler Manifold vacuum Naturally aspirated engine Ram-air intake Scroll-type supercharger Short ram air intake Supercharger Throttle Throttle body Turbocharger Twin-turbo Variable-geometry turbocharger Variable-length intake manifold Warm air intake

Fuel system	Carburetor Common rail Direct injection Fuel filter Fuel injection Fuel pump Fuel tank Gasoline direct injection Indirect injection Injection pump Lean-burn Stratified charge engine Turbo fuel stratified injection Unit injector

Ignition	Contact breaker Magneto Distributor Electrical ballast High tension leads Ignition coil Spark plug Wasted spark

Electrics and engine management	Air–fuel ratio meter Alternator Automatic Performance Control Car battery (lead–acid battery) Crankshaft position sensor Dynamo Drive by wire Electronic control unit Engine control unit Engine coolant temperature sensor Glow plug Idle air control actuator MAP sensor Mass flow sensor Oxygen sensor Starter motor Throttle position sensor

Exhaust system	Automobile emissions control Catalytic converter Diesel particulate filter Exhaust manifold Glasspack Muffler

Engine cooling	Air cooling Antifreeze (ethylene glycol) Core plug Electric fan Fan belt Radiator Thermostat Water cooling Viscous fan (fan clutch)

Other components	Balance shaft Block heater Combustion chamber Cylinder head porting Gasket Motor oil Oil filter Oil pump Oil sludge PCV valve Seal Synthetic oil Underdrive pulleys

Portal Category

Aircraft piston engine components, systems and terminology

Piston engines

Mechanical components	Camshaft Connecting rod Crankpin Crankshaft Cylinder Cylinder head Gudgeon pin Hydraulic tappet Main bearing Obturator ring Oil pump Piston Piston ring Poppet valve Pushrod Rocker arm Sleeve valve Tappet

Electrical components	Alternator Capacitor discharge ignition Dual ignition Electronic fuel injection Generator Ignition system Magneto Spark plug Starter

Terminology	Air-cooled Aircraft engine starting Bore Compression ratio Dead centre Engine displacement Four-stroke engine Horsepower Ignition timing Manifold pressure Mean effective pressure Naturally aspirated Monosoupape Overhead camshaft Overhead valve engine Rotary engine Shock cooling Stroke Time between overhaul Two-stroke engine Valve timing Volumetric efficiency

Propellers

Components	Propeller governor Propeller speed reduction unit Spinner

Terminology	Autofeather Blade pitch Constant-speed Contra-rotating Counter-rotating Scimitar Single-blade Variable-pitch

Engine instruments

Engine controls

Fuel and induction
system

Other systems

This article is issued from Wikipedia - version of the Saturday, April 25, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.