Active shutter 3D system

A pair of CrystalEyes shutter glasses
Functional principle of active shutter 3D systems

An active shutter 3D system (a.k.a. alternate frame sequencing, alternate image, AI, alternating field, field sequential or eclipse method) is a technique of displaying stereoscopic 3D images. It works by only presenting the image intended for the left eye while blocking the right eye's view, then presenting the right-eye image while blocking the left eye, and repeating this so rapidly that the interruptions do not interfere with the perceived fusion of the two images into a single 3D image.

Modern active shutter 3D systems generally use liquid crystal shutter glasses (also called "LC shutter glasses"[1] or "active shutter glasses"[2]). Each eye's glass contains a liquid crystal layer which has the property of becoming opaque when voltage is applied, being otherwise transparent. The glasses are controlled by a timing signal that allows the glasses to alternately block one eye, and then the other, in synchronization with the refresh rate of the screen. The timing synchronization to the video equipment may be achieved via a wired signal, or wirelessly by either an infrared or radio frequency (e.g. Bluetooth, DLP link) transmitter. Historic systems also used spinning discs, for example the Teleview system.

Active shutter 3D systems are used to present 3D films in some theaters, and they can be used to present 3D images on CRT, plasma, LCD, projectors and other types of video displays.

Advantages and disadvantages

Although virtually all ordinary unmodified video and computer systems can be used to display 3D by adding a plug-in interface and active shutter glasses, disturbing levels of flicker or ghosting may be apparent with systems or displays not designed for such use. The rate of alternation required to completely eliminate noticeable flicker depends on image brightness and other factors, but is typically well over 30 image pair cycles per second, the maximum possible with a 60 Hz display. A 120 Hz display, allowing 60 images per second per eye, is widely accepted as flicker-free.

Advantages

Disadvantages

Crosstalk

Crosstalk is the leakage of frames between left eye and right eye.[5] LCDs have exhibited this problem more often than plasma and DLP displays, due to slower pixel response time. LCDs that utilize a strobe backlight,[6] such as nVidia's LightBoost,[7] reduce crosstalk. This is done by turning off the backlight between refreshes, while waiting for the shutter glasses to switch eyes, and also for the LCD panel to finish pixel transitions.

Standards

In March 2011 Panasonic Corporation, together with XPAND 3D, have formulated the M-3DI Standard, which aims to provide industry-wide compatibility and standardization of LC Shutter Glasses. This movement aims to bring about compatibility among manufacturers of 3D TV, computer, notebook, home projection, and cinema with standardized LC shutter glasses that will work across all 3D hardware seamlessly. The current standard is Full HD 3D Glasses.[8]

Field Sequential has been used in video games, VHS and VHD movies and is often referred to as HQFS for DVDs, these systems use wired or wireless LCS glasses.

The Sensio format was used with DVDs using wireless LCS glasses.

Each different active 3D shutter glasses implementation can operate in their own manufacturer-set frequency to match the refresh rate of the display or projector. Therefore, to achieve compatibility across different brands, certain glasses have been developed to be able to adjust to a broad range of frequencies.[9][10]

Timeline

The principle made its public debut remarkably early. In 1922, the Teleview 3-D system was installed in a single theater in New York City. Several short films and one feature-length film were shown by running left-eye and right-eye prints in a pair of interlocked projectors with their shutters operating out of phase. Each seat in the auditorium was equipped with a viewing device containing a rapidly rotating mechanical shutter synchronized with the projector shutters. The system worked, but the expense of the installation and the unwieldiness of the viewers, which had to be supported on adjustable stands, confined its use to this one engagement.

In recent decades, the availability of lightweight optoelectronic shutters has led to an updated revival of this display method. Liquid crystal shutter glasses were first invented by Stephen McAllister of Evans and Sutherland Computer Corporation in the mid-1970s. The prototype had the LCDs mounted to a small cardboard box using duct tape. The glasses were never commercialized due to ghosting, but E&S was a very early adopter of third-party glasses such as the StereoGraphics CrystalEyes in the mid-1980s.

In 1985 3D VHD players became available in Japan from manufacturers such as Victor (JVC), National (Panasonic), and Sharp. Other units were available for field sequential VHS tapes including the Realeyes 3D. A few kits were made available to watch field sequential DVDs. Sensio released their own format which was higher quality than the HQFS DVDs.

Games

SegaScope 3-D Glasses, released in 1987 for Japan and 1989 for North America
Famicom 3D System, released in 1987 for Japan only

The method of alternating frames can be used to render modern 3D games into true 3D, although a similar method involving alternate fields has been used to give a 3D illusion on consoles as old as the Master System and Family Computer. Special software or hardware is used generate two channels of images, offset from each other to create the stereoscopic effect. High frame rates (typically ~100fps) are required to produce seamless graphics, as the perceived frame rate will be half the actual rate (each eye sees only half the total number of frames). Again, LCD shutter glasses synchronized with the graphics chip complete the effect.

In 1982, Sega's arcade video game SubRoc-3D came with a special 3D eyepiece,[11] which was a viewer with spinning discs to alternate left and right images to the player's eye from a single monitor.[12] The game's active shutter 3D system was jointly developed by Sega with Matsushita (now Panasonic).[13]

In 1984, Milton Bradley released the 3D Imager, a primitive form of active shutter glasses that used a motorized rotating disc with transparencies as physical shutters, for the Vectrex. Although bulky and crude, they used the same basic principle of rapidly alternating imagery that modern active shutter glasses still use.

Sega released the SegaScope 3-D for the Master System in 1987 for Japan and in 1988 for North America, where it was the first known electronic device to use LCD Active Shutter glasses. Only eight 3D compatible games were ever released. Nintendo's Famicom also featured a similar Famicom 3D System, which was an LCD shutter headset, released in 1987 only for Japan.

In 1993 Pioneer released the LaserActive system which had a bay for various "PAC's" such as the Mega LD PAC and LD-ROM² PAC. The unit was 3D capable with the addition of the LaserActive 3D goggles (GOL-1) and the adapter (ADP-1).

While the 3D hardware for these earlier video game systems is almost entirely in the hands of collectors it is still possible to play the games in 3D using emulators, for example using a Sega Dreamcast with a Sega Master System emulator in conjunction with a CRT television and a 3D system like the one found in The Ultimate 3-D Collection.

In 1999–2000, a number of companies created stereoscopic LC shutter glasses kits for the Windows PCs which worked with application and games written for Direct3D and OpenGL 3D graphics APIs. These kits only worked with CRT computer displays and employed either VGA pass-through, VESA Stereo or proprietary interface for left–right synchronization.

The most prominent example was the ELSA Revelator glasses, which worked exclusively in Nvidia cards through a proprietary interface based on VESA Stereo. Nvidia later bought the technology and used it in its stereo driver for Windows.

The glasses kits came with driver software which intercepted API calls and effectively rendering the two views in sequence; this technique required twice the performance from the graphic card, so a high-end device was needed. Visual glitches were common, as many 3D game engines relied on 2D effects which were rendered at the incorrect depth, causing disorientation for the viewer. Very few CRT displays were able to support a 120 Hz refresh rate at common gaming resolutions of the time, so high-end CRT display was required for a flicker-free image; and even with a capable CRT monitor, many users reported flickering and headaches.

These CRT kits were entirely incompatible with common LCD monitors which had very high pixel response times, unlike CRT displays. Moreover, the display market swiftly shifted to LCD monitors and most display makers ceased production of CRT monitors in early 2000s, which meant that PC glasses kits shortly fell into disuse and were reduced to a very niche market, requiring a purchase of a used high-end, big diagonal CRT monitor.

SplitFish EyeFX 3D was a stereo 3D shutter glasses kit for the Sony PlayStation 2 released in 2005; it only supported standard-definition CRT TVs. The accessory included a pass-through cable for the PS2 gamepad; when activated, the attached accessory would issue a sequence of rapidly alternating left–right movement commands to the console, producing a kind of "wiggle stereoscopy" effect additionally aided by the wired LC shutter glasses which worked in sync with these movements.[14] The kit arrived too late in the product cycle of the console when it was effectively replaced by the PlayStation 3, and only a few games were supported, so it was largely ignored by gamers.[15]

The USB-based Nvidia 3D Vision kit released in 2008 supports CRT monitors capable of 100, 110, or 120 Hz refresh rates, as well as 120 Hz LCD monitors.

Hardware

Active shutter 3D system providers

There are many sources of low-cost 3D glasses. IO glasses are the most common glasses in this category. XpanD 3D is a manufacturer of shutter glasses, with over 1000 cinemas currently using XpanD glasses.[16] With the release of this technology to the home-viewer market as of 2009, many other manufacturers are now developing their own LC shutter glasses, such as Unipolar International Limited, Accupix Co., Ltd, Panasonic, Samsung, and Sony.

The M-3DI Standard, announced by Panasonic Corporation together with XPAND 3D in March 2011, aims to provide industry-wide compatibility and standardization of LC (Active) Shutter Glasses.

Samsung has developed active 3D glasses that are 2 ounces (57 g) and utilize lens and frame technology pioneered by Silhouette, who creates glasses for NASA.[17]

Nvidia makes a 3D Vision kit for the PC; it comes with 3D shutter glasses, a transmitter, and special graphics driver software. While regular LCD monitors run at 60 Hz, a 120 Hz monitor is required to use 3D Vision.

Other well known providers of active 3D glasses include EStar America and Optoma. Both companies produce 3D Glasses compatible with a variety of technologies, including RF, DLP Link and Bluetooth.

DLP 3D

In 2007, Texas Instruments introduced stereo 3D capable DLP solutions to its OEMs,[18] Samsung and Mitsubishi then introduced the first 3D ready DLP televisions, and DLP 3D projectors came later.

These solutions utilize the inherent speed advantage of the Digital Micro-mirror Device (DMD) to sequentially generate a high refresh rate for the left and right views required for stereoscopic imaging.

DLP 3D technology uses the SmoothPicture wobulation algorithm and relies on the properties of modern 1080p60 DMD imagers. It effectively compacts two L/R views into a single frame by using a checkerboard pattern, only requiring a standard 1080p60 resolution for stereoscopic transmission to the TV. The claimed advantage of this solution is increased spatial resolution, unlike other methods which cut vertical or horizontal resolution in half.

The micromirrors are organized in a so-called "offset-diamond pixel layout" of 960×1080 micromirrors, rotated 45 degrees, with their center points placed in the center of "black" squares on the checkerboard. The DMD employs full-pixel wobulation to display the complete 1080p image as two half-resolution images in a fast sequence. The DMD operates at twice the refresh rate, i.e. 120 Hz, and the complete 1080p picture is displayed in two steps. On the first cadence, only half of the original 1080p60 image is displayed – the pixels that correspond to the "black" squares of the checkerboard pattern. On the second cadence, the DMD array is mechanically shifted (wobulated) by one pixel, so the micromirrors are now in a position previously occupied by the gaps, and another half of the image is displayed – this time, the pixels that correspond to the "white" squares.[19][20]

A synchronization signal is then generated to synchronize the screen's refresh with LC shutter glasses worn by the viewer, using Texas Instruments' proprietary mechanism called DLP Link. DLP Link keeps sync by embedding briefly-flashed white frames during the display's blanking interval, which are picked up by the LC shutter glasses.[21]

Plasma TV

Plasma display panels are inherently high-speed devices as well, since they use pulse-width modulation to maintain the brightness of individual pixels, making them compatible with sequential method involving shutter glasses. Modern panels feature pixel driving frequency of up to 600 Hz and allow 10-bit to 12-bit color precision with 1024 to 4096 gradations of brightness for each subpixel.

Samsung Electronics launched 3D ready PDP TVs in 2008, a "PAVV Cannes 450" in Korea and PNAx450 in the UK and the US. The sets utilize the same checkerboard pattern compression scheme as their DLP TVs, though only at the native resolution of 1360×768 pixels and not at HDTV standard 720p, making them only usable with a PC.

Matsushita Electric (Panasonic) prototyped the "3D Full-HD Plasma Theater System" on CES 2008. The system is a combination of a 103-inch PDP TV, a Blu-ray Disc player and shutter glasses. The new system transmits 1080i60 interlaced images for both right and left eyes, and the video is stored on 50-gigabyte Blu-ray using the MPEG-4 AVC/H.264 compression Multiview Video Coding extension.

LCD

Formerly, LCDs were not very suitable for stereoscopic 3D due to slow pixel response time. Liquid crystal displays have traditionally been slow to change from one polarization state to another. Users of early 1990s laptops are familiar with the smearing and blurring that occurs when something moves too fast for the LCD to keep up.

LCD technology is not usually rated by frames per second but rather the time it takes to transition from one pixel color value to another pixel color value. Normally, a 120 Hz refresh is displayed for a full 1/120 second (8.33 milliseconds) due to sample-and-hold, regardless of how quickly an LCD can complete pixel transitions. Recently, it became possible to hide pixel transitions from being seen, using strobe backlight technology, by turning off the backlight between refreshes,[22] to reduce crosstalk. Newer LCD televisions, including high end Sony and Samsung 3D TVs, now utilize a strobed backlight or scanning backlight to reduce 3D crosstalk during shutter glasses operation.

Therapeutic alternating occlusion

In vision therapy of amblyopia and of intermittent central suppression, liquid crystal devices have been used for purposes of enhanced occlusion therapy. In this scenario, the amblyopic patient wears electronically programmable liquid crystal glasses or goggles for continuously for several hours during regular everyday activities. Wearing the device encourages or forces the patient to use both eyes alternatingly, similar to eye patching, but rapidly alternating in time. The aim is to circumvent the patient's tendency to suppress the field of view of the weaker eye and to train the patient's capacity for binocular vision. The goggles mostly feature a much slower flicker rate than the more well-known active shutter 3D glasses.

See also

References

  1. "LC shutter glasses provide 3-D display for simulated flight", Information Display Magazine, Vol. 2, Issue 9, September 1986
  2. "Active Shutter 3D Technology for HDTV", PhysOrg, September 25, 2009
  3. Archived May 16, 2009, at the Wayback Machine.
  4. Universal 3D Shutter Glass.
  5. 3D crosstalk during shutter glasses operation
  6. High speed video of nVidia LightBoost, illustrating strobe backlight action
  7. nVidia LightBoost backlight
  8. HDfury (downloaded 25 July 2013)
  9. XPAND (downloaded 25 July 2013)
  10. SubRoc-3D at the Killer List of Videogames
  11. Bernard Perron & Mark J. P. Wolf (2008), Video game theory reader two, p. 158, Taylor & Francis, ISBN 0-415-96282-X
  12. http://flyers.arcade-museum.com/?page=thumbs&db=videodb&id=1106
  13. "EyeFX 3D (Version 2.30)". Psillustrated.com. Retrieved 2011-03-30.
  14. "3D Eye FX Adapter by SplitFish Review / Preview for PlayStation 2 (PS2)". Cheatcc.com. Retrieved 2011-03-30.
  15. "The best is yet to come: 3D technology continues to evolve and win audience approval", January 1, 2010
  16. "Samsung crafts 'world's lightest' 3D glasses in partnership with Silhouette", Jan.3, 2011
  17. "3D TV – 3D DLP HDTV – 3D Home Theater – 3D | DLP – Texas Instruments". Dlp.com. Retrieved 2011-03-30.
  18. (PDF) http://web.archive.org/web/20110409182634/http://www.informationdisplay.org/issues/2009/07/art5/art5.pdf. Archived from the original (PDF) on April 9, 2011. Retrieved December 31, 2010. Missing or empty |title= (help)
  19. "What's on HDTV?: An Eye on DLP, No. 3". Whatsonhdtv.blogspot.com. 2005-07-26. Retrieved 2011-03-30.
  20. "DLP Link". Texas Instruments.
  21. AnandTech article, mentioning the LightBoost strobe backlight technique

External links

This article is issued from Wikipedia - version of the Saturday, April 30, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.