Stabilizer (ship)

This article is about the nautical term. For other uses, see Stabilizer.
Location and diagram of retractable fin stabilizers on a ship.
Ship stabilizers: a fixed fin stabilizer (foreground centre) and bilge keels (left background).

Ship stabilizers are fins or rotors mounted beneath the waterline and emerging laterally from the hull to reduce a ship's roll due to wind or waves. Active fins are controlled by a gyroscopic control system. When the gyroscope senses the ship roll, it changes the fins' angle of attack to exert force to counteract the roll. Fixed fins and bilge keels do not move; they reduce roll by hydrodynamic drag exerted when the ship rolls. Stabilizers are mostly used on ocean-going (blue water) ships.

Function

Fins work by producing lift or downforce when the vessel is in motion. The lift produced by the fins should work against the roll moment of the vessel. To accomplish this two wings, each installed underwater on either side of the ship, are used. Stabilizers can be:

Stabilizer movement is similar to that of aircraft ailerons. Some types of fins, especially the ones installed on larger ships, are provided with flaps, that increase the fin lift by about 15%. Stabilizer control needs to consider numerous variables that change quickly: wind, waves, ship motion, draft, etc. Fin stabilizers are vastly more efficient at higher velocities and lose effectiveness when the ship is under a minimum speed.[1] Stabilization solutions at anchor or at low speed include actively-controlled fins (such as the stabilisation at rest system developed by Rolls Royce[2] that oscillate to counteract wave motion), and rotary cylinders employing the Magnus effect. The latter two systems are retractable, allowing for a thinner vessel profile when docking, and reducing drag while cruising.

Fuel consumption and carbon emission

Fin stabilizers are used to reduce the roll motion of the ship and improve the passengers' comfort; however, they can be a considerable hydro dynamic brake for the ship. Stabilizers can reduce a ship's speed due to an increase in hydrodynamic drag. This increases fuel consumption and CO2 emissions. Some ships employ systems to reduce the stabilizers energy dissipation by using computers to control their motion. This reduces their fuel consumption and CO2 emissions.

History

Two 25 ton gyroscopes installed on the USS Henderson transport during construction in 1917, the first large ship to be gyroscopically stabilized.

The bilge keel is an early 20th-century stabilizing innovation, not as effective at reducing roll, but easier to install, and does not require space inside the hull.

An earlier stabilization technology was gyroscopic stabilization. The World War I transport USS Henderson, completed in 1917, was the first large ship with gyro stabilizers (right). It had two 25 ton, 9 ft diameter flywheels mounted near the center of the ship, spun at 1100 RPM by 75 HP AC motors. The gyroscopes' cases were mounted on vertical bearings. When a small sensor gyroscope on the bridge sensed a roll, a servomotor would rotate the gyros about a vertical axis in a direction so their precession would counteract the roll. In tests this system was able to reduce roll to 3 degrees in the roughest seas. The ship Conte di Savoia, which first sailed in November 1932, had three flywheels which were 13 feet in diameter and weighed 108 tons. Gyroscope stabilization was replaced by fin stabilization due to its lower weight and bulk.

The first mention of automatic stabilizers for ships was in 1932 by an engineer working for General Electric.[3]

The first use of fin stabilizers on a ship was by a Japanese cruise liner in 1933.[4]

In 1934 a Dutch liner introduced one of the world's most unusual ship stabilizer systems, in which two large tubes were mounted on each side of the ship's hull with the bottom of the tubes open to the sea. The top of the tubes had compressed air or steam pumped in. As the ship rolled, the side it was rolling to would fill with water and then compressed air or steam would be injected to push the water down, countering the roll.[5]

In 2011 the first fuel saving stabilizer control to have been proven to improve ship speed, and to reduce fuel consumption and CO2 emissions when using stabilizers was installed on board a passenger ship.

Wikimedia Commons has media related to Ship stabilizers.

See also

References

[1]

  1. http://www.pinfabb.com
This article is issued from Wikipedia - version of the Wednesday, March 16, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.