Sydney Steam Motor Tram

NSWGT Steam Motor Trams (Sydney)
Baldwin Tram Motor No. 7 at Balmain, New South Wales
Manufacturer	Baldwin Locomotive Works Randwick Tramway Workshops Henry Vale T. Wearne
Designer	Baldwin Locomotive Works
Constructed	1879-1923
Number built	123
Specifications
Length	17 feet 2 inches (5,232.400 mm)
Width	8 feet 6 inches (2,590.800 mm)
Weight	14.3 t
Maximum speed	20–km/h
Gauge	4 feet 8 ¹⁄₂ inches (1,435.100 mm)

Sydney Steam motor and trailer car. 1879

The Steam tram motors were built for and operated by the New South Wales Government Tramways of Australia.

History

Steam trams were introduced when four steam tram motors imported to Sydney as a temporary transport for the International Exhibition of 1879. It was built at the Baldwin Locomotive Works, Philadelphia, U.S.A. and hauled double decker trailers conveying passengers from the Redfern railway terminus to near the Botanic Gardens ^[1]

Beyer Peacock Steam Tram No 2464 of 1885 was exported to Australia in 1886 as a trial unit by the NSWGT for comparison against the Baldwin steam tram. The Baldwin design prevailed and this engine returned to the UK in 1889 to become Beyer Peacock works shunter No.2. The engine is rumoured to have fallen into the sea on its way from New South Wales to Manchester, before delivery to Beyer Peacock.^[2]

Design

The steam tram motor is basically a small enclosed saddle tank locomotive steam motor with four driving wheels in an 0-4-0 arrangement. A wooden cab encloses the entire locomotive, which features five windows along each side. Access to the cab is through doors from either the front or back platform. The tram is powered by an orthodox locomotive type boiler, American bar type framing, conventional "D" type slide valves and spring suspension. Coke and later coal was carried in a bunker on the rear platform and water in the semi-circular saddle tank.

Typical specifications for an 11" Baldwin steam tram motor:

Cylinders: 11" diameter x 16" stroke
Tractive Effort: 120 psi steam, 5,500 lb at 10 mph
Weight: 14 tons 2 cwt
Length: 17 feet 2 inches
Width: 8 feet 6 inches

Service

The Redfern to Botanic Gardens tramway was planned to operate for the duration of the exhibition. Proving so popular an extension to Randwick was opened in 1880. The peak of steam working was reached during 1894, when the length of the tramway reached 40 miles (64.7 km) when there were over 100 steam trams in service. In 1905-6 steam tram routes were replaced by electric trams with steam trams gradually relegated to outer suburbs.

Steam Tram Motors in service were:

Steam Tram Motors
Builder	Date	Cyl Diam.	Original Nos.	Total
Baldwin	1879	11 inch	1,2,3,4	4
Baldwin	1880	11 inch	5-10	6
Baldwin	1881	10 inch	11,13,15-18,26	7
Baldwin	1881	11 inch	12, 14, 19-25	9
Baldwin	1881	9 inch	27-30	4
Baldwin	1882	9 inch	31-33	3
Baldwin	1882	10 inch	44,45	2
Baldwin	1882	11 inch	34-41	8
Baldwin	1883	10 inch	(2nd) 46,47-49,51-54,56,57	10
Baldwin	1884	11 inch	58-69	12
Baldwin	1885	11 inch	77-96	20
Baldwin	1891	11 inch	(3rd) 76,(2nd) 97,98-110	15
Henry Vale	1890	11 inch	(2nd) 50,(2nd) 70 (2nd) 75	7
Henry Vale	1891	11 inch	(2nd) 5,(Rly) 12(2nd) 13,(2nd) 27,(2nd) 28,(2nd) 76	6
T. Wearne	1884	10 inch	76	1
T. Wearne	1886	10 inch	97	1
Randwick Workshops	1916	11 inch	126A-128A	3
Randwick Workshops	1917	11 inch	129A,130A	2
Randwick Workshops	1923	11 inch	131A,132A	2
Randwick Workshops	1957		body only built for processions	1

Demise and Preservation

The last NSWGT steam motor was withdrawn from service in 1937 and replaced by a trolley bus service. Preserved trams are:

Steam Tram Motor No. 1A, owned by Powerhouse Museum^[3] The identity No.1A was applied by the Powerhouse Museum. It is actually Henry Vale & Co of Sydney built Steam Motor 28a. Makers number 52. ^[4]
Steam Tram Motor No. 103a, [1891] at Valley Heights Steam Tramway^[5] Built by Baldwin Locomotive Works in Philadelphia, Pennsylvania, USA. Makers number 11676.
Steam Tram Motor No. 100, [1891] at Museum of Transport and Technology, Auckland. Built by Baldwin Locomotive Works in Philadelphia, Pennsylvania, USA. Makers number 11885.

Gallery

Early Sydney Tram
Sydney tram, c.1885
2 trailers
'John Bull'
No. 1A Top View
Tram Motor No. 1A
Tram Motor No. 1A
No. 1A Side View
Tram Motor 103A
Tram Motor 103A
103A Driving Wheel
103A Backplate

References

↑ MacCowan, Ian. The Tramways of New South Wales.
↑ "The “Odd-Ball” Steam Tram Motor" (PDF).
↑ "Steam Tram Motor No. 1A, 1898". Powerhouse Museum.
↑ Steaming Down Argent Street - A History of the Broken Hill Steam Tramways 1902-1926.
↑ "Tram 103a". Valley Heights Steam Tramway.

Trams and light rail in Sydney

Current network

Lines	Dulwich Hill Line CBD and South East Light Rail (under construction) Parramatta Light Rail (proposed)

Fleet	Active: Urbos 3 Withdrawn: Urbos 2 Variotram Future: Citadis X05

Former network

Depots	Randwick Workshops Dowling Street Fort Macquarie Leichhardt Manly Newtown North Sydney Ridge Street Rozelle Rushcutters Bay Tempe Ultimo Waverley

Fleet	Classification System Steam Motors C class D class E class F class G class H class J class K class L class L/P class M class N class O class O/P class P class P/R1 class R class R1 class

Other

Sydney Tramway Museum

This article is issued from Wikipedia - version of the Monday, February 01, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.