Violin making and maintenance

Making an instrument of the violin family may be done in different ways, many of which have changed very little in nearly 500 years since the first violins were made. Some violins, called "bench-made" instruments, are made by a single individual, either a master maker, or an amateur working alone. Several people may participate in the making of a "shop-made" instrument, working under the supervision of a master. Various levels of "trade violin" exist, often mass-produced by workers who each focus on a small part of the overall job, with or without the aid of machinery.

"Setting up" a violin is generally considered to be a separate activity, and may be done many times over the lengthy service life of the instrument. Setup includes fitting and trimming tuning pegs, surfacing the fingerboard, carving the soundpost and bridge, adjusting the string spacing and action height, and other tasks related to putting the finished instrument into playing condition and optimizing its voice and response.

Violin maintenance goes on as long as the instrument is to be kept in playing condition, and includes tasks such as replacing strings, positioning the soundpost and bridge, lubricating pegs and fine tuners, resurfacing the fingerboard, attending to the instrument's finish, and restoring or replacing parts of the violin or its accessories which have suffered wear or damage.

Making violins

A new violin scroll being carved.

The outer contour of a new violin, one of the more important aspects of the instrument, is designed by the violin maker, and today the outlines of the old masters' violins are usually used. Different methods of violin making include using an inside mould, an outside mould, or building "on the back" without a mould.

The "inside mould" approach starts with a set of plans, which include a drawing of the outer shape of the instrument. From these plans a template is constructed, which can be made from thin metal or other materials, and is a flat "half-violin" shape. The template is used to construct a mould, which is a violin-shaped piece of wood, plywood, MDF or similar material approximately 12 mm or 1/2" thick.

Around the mould are built the sides (or ribs), which are flat pieces of wood curved by means of careful heating. The completed "garland" of ribs, blocks, and linings is removed from the mould to allow attachment of the separately carved top and back. When the body is complete, the neck, which is carved out of a separate piece of wood (usually maple), is set in its mortise to complete the basic structure of the instrument, after which it is varnished.

Violin taken down, with upright soundpost visible through the sound hole.

Vital to the sound and playability of the instrument is setup, which includes adjusting the neck angle if needed, fitting the pegs so they turn smoothly and hold firmly, dressing the fingerboard to the proper scooped shape, fitting the soundpost and bridge, adjusting the tailgut and installing the tailpiece, and stringing up. A removable chinrest may be put on at this time.

Then the instrument begins the "playing-in" process, as its parts adjust to the string tension. The sound of a violin is said to "open up" in the first weeks and months of use, a process which continues more gradually over the years. However, this process may be aborted at some point. If you put a violin to storage and pull it out a while later, you will notice when you first play that the violin has lost volume (this is a very common sign of violin inactivity), and loss of quality (this is in more severe cases of inactivity). If you put a violin into storage, pull it out a while later, and play it for a few weeks, you will notice the violin's sound start to open up again.

Maintenance

Quite as important as the excellence of the instrument is its care.
— Carl Flesch, from The Art of Violin Playing
Close-up of rosin grains on end of fingerboard.

With careful maintenance, a violin can last and improve for many years. A well-tended violin can outlive many generations of players, so it is wise to take a curatorial view when caring for a violin. Most importantly, if the collected rosin dust is not wiped from the varnish, and left for long enough, it will fuse with the varnish, and become impossible to remove without damage.

Cleaning the rosin off strings can make a striking difference to the sound. A common wine cork serves admirably, quietly scrubbing off the crust of rosin without damaging the winding of the string. A dry microfiber cloth is often recommended; it retains the dust well, but makes a penetrating squeaking noise. A cloth with a little rubbing alcohol is effective, if care is taken to protect the top from the slightest chance of stray droplets of alcohol touching the varnish. The use of alcohol is generally avoided, as it easily damages violin varnish in ways which may be difficult or impossible to restore.

The tuning pegs may occasionally be treated with "peg dope" when they either slip too freely, causing the string to go flat or slack, or when they stick, making tuning difficult. Some players and luthiers use a small amount of ordinary blackboard chalk on pegs to cure slippage. "Peg drops" (a solution of rosin in alcohol) may occasionally be used to treat slipping pegs, but that is a temporary solution at best; quite often slipping pegs have shafts which are no longer smoothly conical, and should be refitted or replaced.

The violin will benefit from occasional checks by a technician, who will know if repairs need to be made.

Violinists generally carry replacement sets of strings with their instruments to have a spare available in case one breaks. Even before breaking, worn strings may begin to sound tired and to become "false" over time, producing an unreliable pitch. Another common problem with strings is unravelling of the metal winding. Strings may need replacement every two or three months with frequent use. The higher strings require replacement more frequently than the lower strings since they are lighter in construction to produce a higher sound– fortunately their lighter weight also means they cost less. The price of strings varies, and the quality of the strings strongly influences the timbre of the sound produced. A teacher can advise students how often to change strings, as it depends on how much and how seriously one plays.

For the bow, the only real maintenance is regular cleaning of the stick with a cloth, and re-hairing. In the course of playing the violin, hairs are often lost from the bow, making it necessary to have it rehaired periodically, which is done by professionals at roughly the cost of a new set of strings. The old horse hair is replaced with new hair. Other maintenance may include replacing the wire lapping and leather grip, or lubricating the screw. Large cracks and breakages in the bow are usually fatal; they cannot be repaired like the body of the instrument can. A bow which has warped and is no longer straight can sometimes be bent back to true or re-cambered, but this must be done with heat by a craftsman, and it is not always successful or worthwhile.

Loosening the hair when the bow is not being used helps keep the bow from becoming "sprung," or losing its camber, and the hair from becoming stretched. There are now bows available made from fiberglass or carbon composite which are less fragile.

Sound post adjustment

Main article: Sound post

The position of the sound post inside the violin is critical, and moving it by very small amounts can make a substantial difference in the sound quality of an instrument. The thickness of the post is important as well. Sound post adjustment is as much art as science, depending on the ears, experience, structural sense, and sensitive touch of the luthier. Moving the sound post has very complex consequences on the sound; in the end, it is the ear of the person doing the adjusting that determines the desired location of the post.

Here are some rough guides to how sound post placement influences the sound quality of the instrument:

Schools

The traditional path into violin making is through apprenticing under an experienced luthier. However, there are also schools, and classes within universities, which may focus on different areas of violin making or repair, and others include auxiliary aspects of lutherie, such as playing, technical illustration and photography. Courses vary in length from several weeks to three or four years.


Belgium

Brazil

Canada

Czech Republic

England

Finland

Germany

Italy

Mexico

Norway

Scotland

Switzerland

United States

See also

Further reading

External links

This article is issued from Wikipedia - version of the Thursday, March 17, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.