DDR2 SDRAM

Two PC2-6400 modules encased in heat spreaders
PC2-6400 DDR2 SO-DIMM (for notebooks)

DDR2 SDRAM is a double data rate synchronous dynamic random-access memory interface. It superseded the original DDR SDRAM specification, and is superseded by DDR3 SDRAM (launched in 2007). DDR2 DIMMs are neither forward compatible with DDR3 nor backward compatible with DDR.

In addition to double pumping the data bus as in DDR SDRAM (transferring data on the rising and falling edges of the bus clock signal), DDR2 allows higher bus speed and requires lower power by running the internal clock at half the speed of the data bus. The two factors combine to produce a total of four data transfers per internal clock cycle.

Since the DDR2 internal clock runs at half the DDR external clock rate, DDR2 memory operating at the same external data bus clock rate as DDR results in DDR2 being able to provide the same bandwidth but with higher latency. Alternatively, DDR2 memory operating at twice the external data bus clock rate as DDR may provide twice the bandwidth with the same latency. The best-rated DDR2 memory modules are at least twice as fast as the best-rated DDR memory modules.

The storage limit of a single memory module based on DDR2 SDRAM is 4 GiB.[1][2]

Overview

Comparison of memory modules for desktop PCs (DIMM).
Comparison of memory modules for portable/mobile PCs (SO-DIMM).

The key difference between DDR2 and DDR SDRAM is the increase in prefetch length. In DDR SDRAM, the prefetch length was two bits for every bit in a word; whereas it is four bits in DDR2 SDRAM. During an access, four bits were read or written to or from a four-bit-deep prefetch queue. This queue received or transmitted its data over the data bus in two data bus clock cycles (each clock cycle transferred two bits of data. Increasing the prefetch length allowed DDR2 SDRAM to double the rate at which data could be transferred over the data bus without a corresponding doubling in the rate at which the DRAM array could be accessed. DDR2 SDRAM was designed with such a scheme to avoid an excessive increase in power consumption.

DDR2's bus frequency is boosted by electrical interface improvements, on-die termination, prefetch buffers and off-chip drivers. However, latency is greatly increased as a trade-off. The DDR2 prefetch buffer is four bits deep, whereas it is two bits deep for DDR. While DDR SDRAM has typical read latencies of between two and three bus cycles, DDR2 may have read latencies between three and nine cycles, although the typical range is between four and six. Thus, DDR2 memory must be operated at twice the data rate to achieve the same latency.

Another cost of the increased bandwidth is the requirement that the chips are packaged in a more expensive and difficult to assemble BGA package as compared to the TSSOP package of the previous memory generations such as DDR SDRAM and SDR SDRAM. This packaging change was necessary to maintain signal integrity at higher bus speeds.

Power savings are achieved primarily due to an improved manufacturing process through die shrinkage, resulting in a drop in operating voltage (1.8 V compared to DDR's 2.5 V). The lower memory clock frequency may also enable power reductions in applications that do not require the highest available data rates.

According to JEDEC[3] the maximum recommended voltage is 1.9 volts and should be considered the absolute maximum when memory stability is an issue (such as in servers or other mission critical devices). In addition, JEDEC states that memory modules must withstand up to 2.3 volts before incurring permanent damage (although they may not actually function correctly at that level).

Specification standards

Chips and modules

For use in computers, DDR2 SDRAM is supplied in DIMMs with 240 pins and a single locating notch. Laptop DDR2 SO-DIMMs have 200 pins and often come identified by an additional S in their designation. DIMMs are identified by their peak transfer capacity (often called bandwidth).

Standard name

 

Memory clock

(MHz)

Cycle time

(ns)

I/O bus clock

(MHz)

Data rate

(MT/s)

Module name

 

Peak transfer rate

(MB/s)

Timings[4][5]

(CL-tRCD-tRP)

CAS latency

(ns)

DDR2-400B
DDR2-400C
100 10 200 400 PC2-3200 3200 4-4-4
3-3-3
20
15
DDR2-533B
DDR2-533C
133.33 7.5 266.67 533.33 PC2-4200* 4266.67 4-4-4
3-3-3
15
11.25
DDR2-667C
DDR2-667D
166.67 6 333.33 666.67 PC2-5300* 5333.33 5-5-5
4-4-4
15
12
DDR2-800C
DDR2-800D
DDR2-800E
200 5 400 800 PC2-6400 6400 6-6-6
5-5-5
4-4-4
15
12.5
10
DDR2-1066E
DDR2-1066F
266.67 3.75 533.33 1066.67 PC2-8500* 8533.33 7-7-7
6-6-6
13.125
11.25

Relative speed comparison between similar modules

PC5300 5-5-5 PC5300 4-4-4 PC6400 6-6-6 PC6400 5-5-5 PC6400 4-4-4
PC2-3200 4-4-4 % % +33% +60% %
PC2-3200 3-3-3 % % = +20% %
PC2-4200 4-4-4 % % = +21% %
PC2-4200 3-3-3 % % -24% -9% %
PC2-5300 5-5-5 % % = +21% %
PC2-5300 4-4-4 % % -19% -3% %
PC2-6400 6-6-6 % % = +20% %
PC2-6400 5-5-5 % % -16% = %
PC2-6400 4-4-4 % % -33% -20% %
PC2-8500 7-7-7 % % -12% +6% %
PC2-8500 6-6-6 % % -25% -9% %

* Some manufacturers label their DDR2 modules as PC2-4300, PC2-5400 or PC2-8600 instead of the respective names suggested by JEDEC. At least one manufacturer has reported this reflects successful testing at a higher-than-standard data rate[6] whilst others simply round up for the name.

Note: DDR2-xxx denotes data transfer rate, and describes raw DDR chips, whereas PC2-xxxx denotes theoretical bandwidth (with the last two digits truncated), and is used to describe assembled DIMMs. Bandwidth is calculated by taking transfers per second and multiplying by eight. This is because DDR2 memory modules transfer data on a bus that is 64 data bits wide, and since a byte comprises 8 bits, this equates to 8 bytes of data per transfer.

In addition to bandwidth and capacity variants, modules can

  1. Optionally implement ECC, which is an extra data byte lane used for correcting minor errors and detecting major errors for better reliability. Modules with ECC are identified by an additional ECC in their designation. PC2-4200 ECC is a PC2-4200 module with ECC. An additional P can be added at the end of the designation, P standing for parity (ex : PC2-5300P).
  2. Be "registered" ("buffered"), which improves signal integrity (and hence potentially clock rates and physical slot capacity) by electrically buffering the signals at a cost of an extra clock of increased latency. Those modules are identified by an additional R in their designation, whereas non-registered (a.k.a. "unbuffered") RAM may be identified by an additional U in the designation. PC2-4200R is a registered PC2-4200 module, PC2-4200R ECC is the same module but with additional ECC.
  3. Be fully buffered modules, which are designated by F or FB and do not have the same notch position as other classes. Fully buffered modules cannot be used with motherboards that are made for registered modules, and the different notch position physically prevents their insertion.

Note: registered and un-buffered SDRAM generally cannot be mixed on the same channel.

Note that the highest-rated DDR2 modules in 2009 operate at 533 MHz (1066 MT/s), compared to the highest-rated DDR modules operating at 200 MHz (400 MT/s). At the same time, the CAS latency of 11.2 ns = 6 / (bus clock rate) for the best PC2-8500 modules is comparable to that of 10 ns = 4 / (bus clock rate) for the best PC-3200 modules.

Debut

DDR2 was introduced in the second quarter of 2003 at two initial clock rates: 200 MHz (referred to as PC2-3200) and 266 MHz (PC2-4200). Both performed worse than the original DDR specification due to higher latency, which made total access times longer. However, the original DDR technology tops out at a clock rate around 200 MHz (400 MT/s). Higher performance DDR chips exist, but JEDEC has stated that they will not be standardized. These chips are mostly standard DDR chips that have been tested and rated to be capable of operation at higher clock rates by the manufacturer. Such chips draw significantly more power than slower-clocked chips, but usually offered little or no improvement in real-world performance. DDR2 started to become competitive against the older DDR standard by the end of 2004, as modules with lower latencies became available.[7]

Backward compatibility

DDR2 DIMMs are not backward compatible with DDR DIMMs. The notch on DDR2 DIMMs is in a different position from DDR DIMMs, and the pin density is higher than DDR DIMMs in desktops. DDR2 is a 240-pin module, DDR is a 184-pin module. Notebooks have 200-pin SO-DIMMs for DDR and DDR2; however, the notch on DDR2 modules is in a slightly different position than on DDR modules.

Higher-speed DDR2 DIMMs can be mixed with lower-speed DDR2 DIMMs, although the memory controller will operate all DIMMs at same speed as the lowest-speed DIMM present.

Relation to GDDR memory

The first commercial product to claim using the "DDR2" technology was the NVIDIA GeForce FX 5800 graphics card. However, it is important to note that this GDDR2 memory used on graphics cards is not DDR2 per se, but rather an early midpoint between DDR and DDR2 technologies. Using "DDR2" to refer to GDDR2 is a colloquial misnomer. In particular, the performance-enhancing doubling of the I/O clock rate is missing. It had severe overheating issues due to the nominal DDR voltages. ATI has since designed the GDDR technology further into GDDR3, which is based on DDR2 SDRAM, though with several additions suited for graphics cards.

GDDR3 and GDDR5 is now commonly used in modern graphics cards and some tablet PCs. However, further confusion has been added to the mix with the appearance of budget and mid-range graphics cards which claim to use "GDDR2". These cards actually use standard DDR2 chips designed for use as main system memory although operating with higher latencies to achieve higher clockrates. These chips cannot achieve the clock rates of GDDR3 but are inexpensive and fast enough to be used as memory on mid-range cards.

See also

References

Further reading

Note**: JEDEC website requires registration ($2,500 membership) for viewing or downloading of these documents: http://www.jedec.org/standards-documents

External links

This article is issued from Wikipedia - version of the Sunday, April 03, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.