Synchronous dynamic random-access memory

Synchronous dynamic random-access memory (SDRAM) is any dynamic random-access memory (DRAM) where the operation of its external pin interface is coordinated by an externally supplied clock signal. DRAM integrated circuits (ICs), between the mid-1970s and -1990s typically had an asynchronous interface, where responses to changes in control signal inputs occur as soon as they are received. SDRAM has a synchronous interface, meaning that a clock signal must be received before it responds to the control inputs. The interfaces of SDRAM ICs is therefore synchronous to the clock signal used. In the family of devices standardized by JEDEC, which are called synchronous DRAMs (SDRAMs), the clock signal is used to drive an internal finite state machine that pipelines incoming commands. The memory is divided into several independent sections of memory called banks, allowing the device to operate on several memory access commands at a time, provided the commands are independent of each other (in an interleaved fashion). This allows SDRAMs to achieve greater concurrency and higher data transfer rates than asynchronous DRAMs.

Pipelining means that the chip can accept a new command before it has finished processing the previous one. In a pipelined write, the write command can be immediately followed by another command, without waiting for the data to be written to the memory array. In a pipelined read, the requested data appears after a fixed number of clock cycles after the read command (latency), clock cycles during which additional commands can be sent.

SDRAM is widely used in computers; after the original SDRAM, further generations of double data rate RAM have entered the mass market – DDR (also known as DDR1), DDR2, DDR3 and DDR4, with the latest generation (DDR4) released in second half of 2014.

SDRAM history

Eight SDRAM ICs on a PC100 DIMM package.

Although the concept of synchronous DRAM has been known since at least the 1970s and was used with early Intel processors, it was only in 1993 that SDRAM began its path to universal acceptance in the electronics industry. In 1993, Samsung introduced its KM48SL2000 synchronous DRAM, and by 2000, SDRAM had replaced virtually all other types of DRAM in modern computers, because of its greater performance.

SDRAM latency is not inherently lower (faster) than asynchronous DRAM. Indeed, early SDRAM was somewhat slower than contemporaneous burst EDO DRAM due to the additional logic. The benefits of SDRAM's internal buffering come from its ability to interleave operations to multiple banks of memory, thereby increasing effective bandwidth.

Today, virtually all SDRAM is manufactured in compliance with standards established by JEDEC, an electronics industry association that adopts open standards to facilitate interoperability of electronic components. JEDEC formally adopted its first SDRAM standard in 1993 and subsequently adopted other SDRAM standards, including those for DDR, DDR2 and DDR3 SDRAM.

SDRAM is also available in registered varieties, for systems that require greater scalability such as servers and workstations.

Today, the world's largest manufacturers of SDRAM include: Samsung Electronics, Panasonic, Micron Technology, and Hynix.

SDRAM timing

There are several limits on DRAM performance. Most noted is the read cycle time, the time between successive read operations to an open row. This time decreased from 10 ns for 100 MHz SDRAM to 5 ns for DDR-400, but has remained relatively unchanged through DDR2-800 and DDR3-1600 generations. However, by operating the interface circuitry at increasingly higher multiples of the fundamental read rate, the achievable bandwidth has increased rapidly.

Another limit is the CAS latency, the time between supplying a column address and receiving the corresponding data. Again, this has remained relatively constant at 10–15 ns through the last few generations of DDR SDRAM.

In operation, CAS latency is a specific number of clock cycles programmed into the SDRAM's mode register and expected by the DRAM controller. Any value may be programmed, but the SDRAM will not operate correctly if it is too low. At higher clock rates, the useful CAS latency in clock cycles naturally increases. 10–15 ns is 2–3 cycles (CL2–3) of the 200 MHz clock of DDR-400 SDRAM, CL4-6 for DDR2-800, and CL8-12 for DDR3-1600. Slower clock cycles will naturally allow lower numbers of CAS latency cycles.

SDRAM modules have their own timing specifications, which may be slower than those of the chips on the module. When 100 MHz SDRAM chips first appeared, some manufacturers sold "100 MHz" modules that could not reliably operate at that clock rate. In response, Intel published the PC100 standard, which outlines requirements and guidelines for producing a memory module that can operate reliably at 100 MHz. This standard was widely influential, and the term "PC100" quickly became a common identifier for 100 MHz SDRAM modules, and modules are now commonly designated with "PC"-prefixed numbers (PC66, PC100 or PC133 - although the actual meaning of the numbers has changed).

SDR SDRAM

The 64 MB of sound memory on the Sound Blaster X-Fi Fatality Pro sound card is built from two Micron 48LC32M8A2 SDRAM chips. They run at 133 MHz (7.5 ns clock period) and have 8-bit wide data buses.[1]

Originally simply known as SDRAM, single data rate SDRAM can accept one command and transfer one word of data per clock cycle. Typical clock frequencies are 100 and 133 MHz. Chips are made with a variety of data bus sizes (most commonly 4, 8 or 16 bits), but chips are generally assembled into 168-pin DIMMs that read or write 64 (non-ECC) or 72 (ECC) bits at a time.

Use of the data bus is intricate and thus requires a complex DRAM controller circuit. This is because data written to the DRAM must be presented in the same cycle as the write command, but reads produce output 2 or 3 cycles after the read command. The DRAM controller must ensure that the data bus is never required for a read and a write at the same time.

Typical SDR SDRAM clock rates are 66, 100, and 133 MHz (periods of 15, 10, and 7.5 ns). Clock rates up to 200 MHz were available.

SDRAM control signals

All commands are timed relative to the rising edge of a clock signal. In addition to the clock, there are 6 control signals, mostly active low, which are sampled on the rising edge of the clock:

Command signals

Bank Selection (BAn)

SDRAM devices are internally divided into either 2, 4 or 8 independent internal data banks. One to three Bank Address inputs (BA0, BA1 and BA2) are used to select which bank a command is directed toward.

Addressing (A10/An)

Many commands also use an address presented on the address input pins. Some commands, which either do not use an address, or present a column address, also use A10 to select variants.

Commands

The commands are defined as follows:

CS RAS CAS WE BAn A10 An Command
H x x x x x x Command inhibit (No operation)
L H H H x x x No operation
L H H L x x x Burst Terminate: stop a burst read or burst write in progress.
L H L H bank L column Read: Read a burst of data from the currently active row.
L H L H bank H column Read with auto precharge: As above, and precharge (close row) when done.
L H L L bank L column Write: Write a burst of data to the currently active row.
L H L L bank H column Write with auto precharge: As above, and precharge (close row) when done.
L L H H bank row Active (activate): open a row for Read and Write commands.
L L H L bank L x Precharge: Deactivate (close) the current row of selected bank.
L L H L x H x Precharge all: Deactivate (close) the current row of all banks.
L L L H x x x Auto refresh: Refresh one row of each bank, using an internal counter. All banks must be precharged.
L L L L 0 0 mode Load mode register: A0 through A9 are loaded to configure the DRAM chip.
The most significant settings are CAS latency (2 or 3 cycles) and burst length (1, 2, 4 or 8 cycles)

All SDRAM generations (SDR and DDRx) use essentially the same commands, with the changes being:

SDRAM construction and operation

For example, a 512 MB SDRAM DIMM (which contains 512 MiB (mebibytes) = 512 × 220 bytes = 536,870,912 bytes exactly), might be made of eight or nine SDRAM chips, each containing 512 Mbit of storage, and each one contributing 8 bits to the DIMM's 64- or 72-bit width. A typical 512 Mbit SDRAM chip internally contains 4 independent 16 MB (MiB) memory banks. Each bank is an array of 8,192 rows of 16,384 bits each. A bank is either idle, active, or changing from one to the other.

The active command activates an idle bank. It presents a two-bit bank address (BA0–BA1) and a 13-bit row address (A0–A12), and causes a read of that row into the bank's array of all 16,384 column sense amplifiers. This is also known as "opening" the row. This operation has the side effect of refreshing the dynamic (capacitive) memory storage cells of that row.

Once the row has been activated or "opened", read and write commands are possible to that row. Activation requires a minimum amount of time, called the row-to-column delay, or tRCD before reads or writes to it may occur. This time, rounded up to the next multiple of the clock period, specifies the minimum number of wait cycles between an active command, and a read or write command. During these wait cycles, additional commands may be sent to other banks; because each bank operates completely independently.

Both read and write commands require a column address. Because each chip accesses eight bits of data at a time, there are 2048 possible column addresses thus requiring only 11 address lines (A0–A9, A11).

When a read command is issued, the SDRAM will produce the corresponding output data on the DQ lines in time for the rising edge of the clock a few clock cycles later, depending on the configured CAS latency. Subsequent words of the burst will be produced in time for subsequent rising clock edges.

A write command is accompanied by the data to be written driven on to the DQ lines during the same rising clock edge. It is the duty of the memory controller to ensure that the SDRAM is not driving read data on to the DQ lines at the same time that it needs to drive write data on to those lines. This can be done by waiting until a read burst has finished, by terminating a read burst, or by using the DQM control line.

When the memory controller needs to access a different row, it must first return that bank's sense amplifiers to an idle state, ready to sense the next row. This is known as a "precharge" operation, or "closing" the row. A precharge may be commanded explicitly, or it may be performed automatically at the conclusion of a read or write operation. Again, there is a minimum time, the row precharge delay, tRP, which must elapse before that bank is fully idle and it may receive another activate command.

Although refreshing a row is an automatic side effect of activating it, there is a minimum time for this to happen, which requires a minimum row access time tRAS delay between an active command opening a row, and the corresponding precharge command closing it. This limit is usually dwarfed by desired read and write commands to the row, so its value has little effect on typical performance.

Command interactions

The no operation command is always permitted, while the load mode register command requires that all banks be idle, and a delay afterward for the changes to take effect. The auto refresh command also requires that all banks be idle, and takes a refresh cycle time tRFC to return the chip to the idle state. (This time is usually equal to tRCD+tRP.) The only other command that is permitted on an idle bank is the active command. This takes, as mentioned above, tRCD before the row is fully open and can accept read and write commands.

When a bank is open, there are four commands permitted: read, write, burst terminate, and precharge. Read and write commands begin bursts, which can be interrupted by following commands.

Interrupting a read burst

A read, burst terminate, or precharge command may be issued at any time after a read command, and will interrupt the read burst after the configured CAS latency. So if a read command is issued on cycle 0, another read command is issued on cycle 2, and the CAS latency is 3, then the first read command will begin bursting data out during cycles 3 and 4, then the results from the second read command will appear beginning with cycle 5.

If the command issued on cycle 2 were burst terminate, or a precharge of the active bank, then no output would be generated during cycle 5.

Although the interrupting read may be to any active bank, a precharge command will only interrupt the read burst if it is to the same bank or all banks; a precharge command to a different bank will not interrupt a read burst.

To interrupt a read burst by a write command is possible, but more difficult. It can be done, if the DQM signal is used to suppress output from the SDRAM so that the memory controller may drive data over the DQ lines to the SDRAM in time for the write operation. Because the effects of DQM on read data are delayed by 2 cycles, but the effects of DQM on write data are immediate, DQM must be raised (to mask the read data) beginning at least two cycles before write command, but must be lowered for the cycle of the write command (assuming the write command is intended to have an effect).

Doing this in only two clock cycles requires careful coordination between the time the SDRAM takes to turn off its output on a clock edge and the time the data must be supplied as input to the SDRAM for the write on the following clock edge. If the clock frequency is too high to allow sufficient time, three cycles may be required.

If the read command includes auto-precharge, the precharge begins the same cycle as the interrupting command.

SDRAM burst ordering

A modern microprocessor with a cache will generally access memory in units of cache lines. To transfer a 64-byte cache line requires eight consecutive accesses to a 64-bit DIMM, which can all be triggered by a single read or write command by configuring the SDRAM chips, using the mode register, to perform eight-word bursts. A cache line fetch is typically triggered by a read from a particular address, and SDRAM allows the "critical word" of the cache line to be transferred first. ("Word" here refers to the width of the SDRAM chip or DIMM, which is 64 bits for a typical DIMM.) SDRAM chips support two possible conventions for the ordering of the remaining words in the cache line.

Bursts always access an aligned block of BL consecutive words beginning on a multiple of BL. So, for example, a four-word burst access to any column address from four to seven will return words four to seven. The ordering, however, depends on the requested address, and the configured burst type option: sequential or interleaved. Typically, a memory controller will require one or the other. When the burst length is one or two, the burst type does not matter. For a burst length of one, the requested word is the only word accessed. For a burst length of two, the requested word is accessed first, and the other word in the aligned block is accessed second. This is the following word if an even address was specified, and the previous word if an odd address was specified.

For the sequential burst mode, later words are accessed in increasing address order, wrapping back to the start of the block when the end is reached. So, for example, for a burst length of four, and a requested column address of five, the words would be accessed in the order 5-6-7-4. If the burst length were eight, the access order would be 5-6-7-0-1-2-3-4. This is done by adding a counter to the column address, and ignoring carries past the burst length. The interleaved burst mode computes the address using an exclusive or operation between the counter and the address. Using the same starting address of five, a four-word burst would return words in the order 5-4-7-6. An eight-word burst would be 5-4-7-6-1-0-3-2.[2] Although more confusing to humans, this can be easier to implement in hardware, and is preferred by Intel for its microprocessors.

If the requested column address is at the start of a block, both burst modes (sequential and interleaved) return data in the same sequential sequence 0-1-2-3-4-5-6-7. The difference only matters if fetching a cache line from memory in critical-word-first order.

SDRAM mode register

Single data rate SDRAM has a single 10-bit programmable mode register. Later double-data-rate SDRAM standards add additional mode registers, addressed using the bank address pins. For SDR SDRAM, the bank address pins and address lines A10 and above are ignored, but should be zero during a mode register write.

The bits are M9 through M0, presented on address lines A9 through A0 during a load mode register cycle.

  1. M9: Write burst mode. If 0, writes use the read burst length and mode. If 1, all writes are non-burst (single location).
  2. M8, M7: Operating mode. Reserved, and must be 00.
  3. M6, M5, M4: CAS latency. Generally only 010 (CL2) and 011 (CL3) are legal. Specifies the number of cycles between a read command and data output from the chip. The chip has a fundamental limit on this value in nanoseconds; during initialization, the memory controller must use its knowledge of the clock frequency to translate that limit into cycles.
  4. M3: Burst type. 0 - requests sequential burst ordering, while 1 requests interleaved burst ordering.
  5. M2, M1, M0: Burst length. Values of 000, 001, 010 and 011 specify a burst size of 1, 2, 4 or 8 words, respectively. Each read (and write, if M9 is 0) will perform that many accesses, unless interrupted by a burst stop or other command. A value of 111 specifies a full-row burst. The burst will continue until interrupted. Full-row bursts are only permitted with the sequential burst type.

Later (double data rate) SDRAM standards use more mode register bits, and provide additional mode registers called Extended Mode registers. The register number is encoded on the bank address pins during the Load Mode Register command. For example, DDR2 SDRAM has a 13-bit Mode Register, a 13-bit Extended Mode Register #1 (EMR1), and a 5-bit Extended Mode Register #2 (EMR2).

Auto refresh

It is possible to refresh a RAM chip by opening and closing (activating and precharging) each row in each bank. However, to simplify the memory controller, SDRAM chips support an "auto refresh" command, which performs these operations to one row in each bank simultaneously. The SDRAM also maintains an internal counter, which iterates over all possible rows. The memory controller must simply issue a sufficient number of auto refresh commands (one per row, 4096 in the example we have been using) every refresh interval (tREF = 64 ms is a common value). All banks must be idle (closed, precharged) when this command is issued.

Low power modes

As mentioned, the clock enable (CKE) input can be used to effectively stop the clock to an SDRAM. The CKE input is sampled each rising edge of the clock, and if it is low, the following rising edge of the clock is ignored for all purposes other than checking CKE. As long as CKE is low, it is permissible to change the clock rate, or even stop the clock entirely.

If CKE is lowered while the SDRAM is performing operations, it simply "freezes" in place until CKE is raised again.

If the SDRAM is idle (all banks precharged, no commands in progress) when CKE is lowered, the SDRAM automatically enters power-down mode, consuming minimal power until CKE is raised again. This must not last longer than the maximum refresh interval tREF, or memory contents may be lost. It is legal to stop the clock entirely during this time for additional power savings.

Finally, if CKE is lowered at the same time as an auto-refresh command is sent to the SDRAM, the SDRAM enters self-refresh mode. This is like power down, but the SDRAM uses an on-chip timer to generate internal refresh cycles as necessary. The clock may be stopped during this time. While self-refresh mode consumes slightly more power than power-down mode, it allows the memory controller to be disabled entirely, which commonly more than makes up the difference.

SDRAM designed for battery-powered devices offers some additional power-saving options. One is temperature-dependent refresh; an on-chip temperature sensor reduces the refresh rate at lower temperatures, rather than always running it at the worst-case rate. Another is selective refresh, which limits self-refresh to a portion of the DRAM array. The fraction which is refreshed is configured using an extended mode register. The third, implemented in Mobile DDR (LPDDR) and LPDDR2 is "deep power down" mode, which invalidates the memory and requires a full reinitialization to exit from. This is activated by sending a "burst terminate" command while lowering CKE.

DDR SDRAM prefetch architecture

DDR SDRAM employs prefetch architecture to allow quick and easy access to multiple data words located on a common physical row in the memory.

The prefetch architecture takes advantage of the specific characteristics of memory accesses to DRAM. Typical DRAM memory operations involve three phases: bitline precharge, row access, column access. Row access is the heart of a read operation, as it involves the careful sensing of the tiny signals in DRAM memory cells; it is the slowest phase of memory operation. However, once a row is read, subsequent column accesses to that same row can be very quick, as the sense amplifiers also act as latches. For reference, a row of a 1 Gbit DDR3 device is 2,048 bits wide, so internally 2,048 bits are read into 2,048 separate sense amplifiers during the row access phase. Row accesses might take 50 ns, depending on the speed of the DRAM, whereas column accesses off an open row are less than 10 ns.

Traditional DRAM architectures have long supported fast column access to bits on an open row. For an 8-bit-wide memory chip with a 2,048 bit wide row, accesses to any of the 256 datawords (2048/8) on the row can be very quick, provided no intervening accesses to other rows occur.

The drawback of the older fast column access method was that a new column address had to be sent for each additional dataword on the row. The address bus had to operate at the same frequency as the data bus. Prefetch architecture simplifies this process by allowing a single address request to result in multiple data words.

In a prefetch buffer architecture, when a memory access occurs to a row the buffer grabs a set of adjacent datawords on the row and reads them out ("bursts" them) in rapid-fire sequence on the IO pins, without the need for individual column address requests. This assumes the CPU wants adjacent datawords in memory, which in practice is very often the case. For instance, when a 64 bit CPU accesses a 16-bit-wide DRAM chip, it will need 4 adjacent 16 bit datawords to make up the full 64 bits. A 4n prefetch buffer would accomplish this exactly ("n" refers to the IO width of the memory chip; it is multiplied by the burst depth "4" to give the size in bits of the full burst sequence). An 8n prefetch buffer on an 8 bit wide DRAM would also accomplish a 64 bit transfer.

The prefetch buffer depth can also be thought of as the ratio between the core memory frequency and the IO frequency. In an 8n prefetch architecture (such as DDR3), the IOs will operate 8 times faster than the memory core (each memory access results in a burst of 8 datawords on the IOs). Thus a 200 MHz memory core is combined with IOs that each operate eight times faster (1600 megabits per second). If the memory has 16 IOs, the total read bandwidth would be 200 MHz x 8 datawords/access x 16 IOs = 25.6 gigabits per second (Gbit/s), or 3.2 gigabytes per second (GB/s). Modules with multiple DRAM chips can provide correspondingly higher bandwidth.

Each generation of SDRAM has a different prefetch buffer size:

Generations of SDRAM

SDRAM feature map
Type Feature changes
SDRAM Vcc = 3.3 V
Signal: LVTTL
DDR1 Access is ≥2 words
Double clocked
Vcc = 2.5 V
2.5 - 7.5 ns per cycle
Signal: SSTL_2 (2.5V)[3]
DDR2 Access is ≥4 words
"Burst terminate" removed
4 units used in parallel
1.25 - 5 ns per cycle
Internal operations are at 1/2 the clock rate.
Signal: SSTL_18 (1.8V)[3]
DDR3 Access is ≥8 words
Signal: SSTL_15 (1.5V)[3]
Much longer CAS latencies
DDR4 Vcc ≤ 1.2 V point-to-point (single module per channel)

SDR SDRAM (Single Data Rate synchronous DRAM)

This type of SDRAM is slower than the DDR variants, because only one word of data is transmitted per clock cycle (single data rate). But this type is also faster than its predecessors EDO-RAM and FPM-RAM which took typically 2 or 3 clocks to transfer one word of data.

DDR(1) SDRAM

Main article: DDR SDRAM

While the access latency of DRAM is fundamentally limited by the DRAM array, DRAM has very high potential bandwidth because each internal read is actually a row of many thousands of bits. To make more of this bandwidth available to users, a double data rate interface was developed. This uses the same commands, accepted once per cycle, but reads or writes two words of data per clock cycle. The DDR interface accomplishes this by reading and writing data on both the rising and falling edges of the clock signal. In addition, some minor changes to the SDR interface timing were made in hindsight, and the supply voltage was reduced from 3.3 to 2.5 V. As a result, DDR SDRAM is not backwards compatible with SDR SDRAM.

DDR SDRAM (sometimes called DDR1 for greater clarity) doubles the minimum read or write unit; every access refers to at least two consecutive words.

Typical DDR SDRAM clock rates are 133, 166 and 200 MHz (7.5, 6, and 5 ns/cycle), generally described as DDR-266, DDR-333 and DDR-400 (3.75, 3, and 2.5 ns per beat). Corresponding 184-pin DIMMs are known as PC-2100, PC-2700 and PC-3200. Performance up to DDR-550 (PC-4400) is available for a price.

DDR2 SDRAM

Main article: DDR2 SDRAM

DDR2 SDRAM is very similar to DDR SDRAM, but doubles the minimum read or write unit again, to 4 consecutive words. The bus protocol was also simplified to allow higher performance operation. (In particular, the "burst terminate" command is deleted.) This allows the bus rate of the SDRAM to be doubled without increasing the clock rate of internal RAM operations; instead, internal operations are performed in units 4 times as wide as SDRAM. Also, an extra bank address pin (BA2) was added to allow 8 banks on large RAM chips.

Typical DDR2 SDRAM clock rates are 200, 266, 333 or 400 MHz (periods of 5, 3.75, 3 and 2.5 ns), generally described as DDR2-400, DDR2-533, DDR2-667 and DDR2-800 (periods of 2.5, 1.875, 1.5 and 1.25 ns). Corresponding 240-pin DIMMS are known as PC2-3200 through PC2-6400. DDR2 SDRAM is now available at a clock rate of 533 MHz generally described as DDR2-1066 and the corresponding DIMMs are known as PC2-8500 (also named PC2-8600 depending on the manufacturer). Performance up to DDR2-1250 (PC2-10000) is available for a price.

Note that because internal operations are at 1/2 the clock rate, DDR2-400 memory (internal clock rate 100 MHz) has somewhat higher latency than DDR-400 (internal clock rate 200 MHz).

DDR3 SDRAM

Main article: DDR3 SDRAM

DDR3 continues the trend, doubling the minimum read or write unit to 8 consecutive words. This allows another doubling of bandwidth and external bus rate without having to change the clock rate of internal operations, just the width. To maintain 800–1600 M transfers/s (both edges of a 400–800 MHz clock), the internal RAM array has to perform 100–200 M fetches per second.

Again, with every doubling, the downside is the increased latency. As with all DDR SDRAM generations, commands are still restricted to one clock edge and command latencies are given in terms of clock cycles, which are half the speed of the usually quoted transfer rate (a CAS latency of 8 with DDR3-800 is 8/(400 MHz) = 20 ns, exactly the same latency of CAS2 on PC100 SDR SDRAM).

DDR3 memory chips are being made commercially,[4] and computer systems using them were available from the second half of 2007,[5] with significant usage from 2008 onwards.[6] Initial clock rates were 400 and 533 MHz, which are described as DDR3-800 and DDR3-1066 (PC3-6400 and PC3-8500 modules), but 667 and 800 MHz, described as DDR3-1333 and DDR3-1600 (PC3-10600 and PC3-12800 modules) are now common.[7] Performance up to DDR3-2800 (PC3 22400 modules) are available for a price.[8]

DDR4 SDRAM

Main article: DDR4 SDRAM

DDR4 SDRAM is the successor to DDR3 SDRAM. It was revealed at the Intel Developer Forum in San Francisco in 2008, and was due to be released to market during 2011. The timing has varied considerably during its development - it was originally expected to be released in 2012,[9] and later (during 2010) expected to be released in 2015,[10] before samples were announced in early 2011 and manufacturers began to announce that commercial production and release to market was anticipated in 2012. DDR4 is expected to reach mass market adoption around 2015, which is comparable with the approximately 5 years taken for DDR3 to achieve mass market transition over DDR2.

The new chips are expected to run at 1.2 V or less,[11][12] versus the 1.5 V of DDR3 chips, and have in excess of 2 billion data transfers per second. They are expected to be introduced at frequency rates of 2133 MHz, estimated to rise to a potential 4266 MHz[13] and lowered voltage of 1.05 V[14] by 2013.

DDR4 will not double the internal prefetch width again, but will use the same 8n prefetch as DDR3.[15] Thus, it will be necessary to interleave reads from several banks to keep the data bus busy.

In February 2009, Samsung validated 40 nm DRAM chips, considered a "significant step" towards DDR4 development[16] since as of 2009, current DRAM chips were only beginning to migrate to a 50 nm process.[17] In January 2011, Samsung announced the completion and release for testing of a 30 nm 2 GB DDR4 DRAM module. It has a maximum bandwidth of 2.13 Gbit/s at 1.2 V, uses pseudo open drain technology and draws 40% less power than an equivalent DDR3 module.[18][19]

Failed successors

In addition to DDR, there were several other proposed memory technologies to succeed SDR SDRAM.

Rambus DRAM (RDRAM)

RDRAM was a proprietary technology that competed against DDR. Its relatively high price and disappointing performance (resulting from high latencies and a narrow 16-bit data channel versus DDR's 64 bit channel) caused it to lose the race to succeed SDR DRAM.

Synchronous-Link DRAM (SLDRAM)

SLDRAM boasted higher performance and competed against RDRAM. It was developed during the late 1990s by the SLDRAM Consortium. The SLDRAM Consortium consisted of about 20 major DRAM and computer industry manufacturers. (The SLDRAM Consortium became incorporated as SLDRAM Inc. and then changed its name to Advanced Memory International, Inc.). SLDRAM was an open standard and did not require licensing fees. The specifications called for a 64-bit bus running at a 200, 300 or 400 MHz clock frequency. This is achieved by all signals being on the same line and thereby avoiding the synchronization time of multiple lines. Like DDR SDRAM, SLDRAM uses a double-pumped bus, giving it an effective speed of 400,[20] 600,[21] or 800 MT/s.

SLDRAM used an 11-bit command bus (10 command bits CA9:0 plus one start-of-command FLAG line) to transmit 40-bit command packets on 4 consecutive edges of a differential command clock (CCLK/CCLK#). Unlike SDRAM, there were no per-chip select signals; each chip was assigned an ID when reset, and the command contained the ID of the chip that should process it. Data was transferred in 4- or 8-word bursts across an 18-bit (per chip) data bus, using one of two differential data clocks (DCLK0/DCLK0# and DCLK1/DCLK1#). Unlike standard SDRAM, the clock was generated by the data source (the SLDRAM chip in the case of a read operation) and transmitted in the same direction as the data, greatly reducing data skew. To avoid the need for a pause when the source of the DCLK changes, each command specified which DCLK pair it would use.[22]

The basic read/write command consisted of (beginning with CA9 of the first word):

SLDRAM Read, write or row op request packet
FLAG CA9 CA8 CA7 CA6 CA5 CA4 CA3 CA2 CA1 CA0
1 ID8 Device ID ID0 CMD5
0 Command code CMD0 Bank Row
0 Row (continued) 0
0 0 0 0 Column

Individual devices had 8-bit IDs. The 9th bit of the ID sent in commands was used to address multiple devices. Any aligned power-of-2 sized group could be addressed. If the transmitted msbit was set, all least-significant bits up to and including the least-significant 0 bit of the transmitted address were ignored for "is this addressed to me?" purposes. (If the ID8 bit is actually considered less significant than ID0, the unicast address matching becomes a special case of this pattern.)

A read/write command had the msbit clear:

A notable omission from the specification was per-byte write enables; it was designed for systems with caches and ECC memory, which always write in multiples of a cache line.

Additional commands (with CMD5 set) opened and closed rows without a data transfer, performed refresh operations, read or wrote configuration registers, and performed other maintenance operations. Most of these commands supported an additional 4-bit sub-ID (sent as 5 bits, using the same multiple-destination encoding as the primary ID) which could be used to distinguish devices that were assigned the same primary ID because they were connected in parallel and always read/written at the same time.

There were a number of 8-bit control registers and 32-bit status registers to control various device timing parameters.

Virtual Channel Memory (VCM) SDRAM

VCM was a proprietary type of SDRAM that was designed by NEC, but released as an open standard with no licensing fees. It is pin-compatible with standard SDRAM, but the commands are different. The technology was a potential competitor of RDRAM because VCM was not nearly as expensive as RDRAM was. A Virtual Channel Memory (VCM) module is mechanically and electrically compatible with standard SDRAM, so support for both depends only on the capabilities of the memory controller. In the late 1990s, a number of PC northbridge chipsets (such as the popular VIA KX133 and KT133) included VCSDRAM support.

VCM inserts an SRAM cache of 16 "channel" buffers, each 1/4 row "segment" in size, between DRAM banks' sense amplifier rows and the data I/O pins. "Prefetch" and "Restore" command, unique to VCSDRAM, copy data between the DRAM's sense amplifier row and the channel buffers, while the equivalent of SDRAM's Read and Write commands specify a channel number to access. Reads and writes may thus be performed independent of the currently active state of the DRAM array, with the equivalent of 4 full DRAM rows being "open" for access at a time. This is an improvement over the 2 open rows possible in a standard 2-bank SDRAM. (There is actually a 17th "dummy channel" used for some operations.)

To read from VCSDRAM, after the Active command, a "Prefetch" command is required to copy data from the sense amplifier array to the channel SDRAM. This command specifies a bank, 2 bits of column address (to select the segment of the row), and 4 bits of channel number. Once this is performed, the DRAM array may be precharged while read commands to the channel buffer continue. To write, first the data is written to a channel buffer (typically previous initialized using a Prefetch command), then a Restore command, with the same parameters as the Prefetch command, copies a segment of data from the channel to the sense amplifier array.

Unlike a normal SDRAM write, which must be performed to an active (open) row, the VCSDRAM bank must be precharged (closed) when the Restore command is issued. An Active command immediately after the Restore command specifies the DRAM row completes the write to the DRAM array. There is, in addition, a 17th "dummy channel" which allows writes to the currently open row. It may not be Read from, but may be Prefetched to, Written to, and Restored to the sense amplifier array.[23][24]

Although normally a segment is Restored to the same memory address as it was Prefetched from, the channel buffers may also be used for very efficient copying or clearing of large, aligned memory blocks. (The use of quarter-row segments is driven by the fact that DRAM cells are narrower than SRAM cells. The SRAM bits are designed to be 4 DRAM bits wide, and are conveniently connected to one of the 4 DRAM bits they straddle.) Additional commands prefetch a pair of segments to a pair of channels, and an optional command combines prefetch, read, and precharge to reduce the overhead of random reads.

Virtual Channel SDRAM commands[25]
CS RAS CAS WE BA A12–11 A10 A9 A8 A7 A6 A5 A4–2 A1–0 Command
H x x x x — x — Command inhibit (No operation)
L H H H x — x — No operation
L H H L bank channel AP channel L L L x segment Prefetch (auto-precharge if AP=H)
L H H L bank x x x L L H x segment Prefetch to dummy
L H H L bank channel AP channel L H x x segment Pair prefetch (auto-precharge if AP=H)
L H H L bank channel AP channel H L x x segment Restore (auto-precharge if AP=H)
L H H L bank x L x H H — x — Precharge bank
L H H L x x H x H H — x — Precharge all banks
L H L H x channel x channel column Read channel
L H L L L channel x channel column Write channel
L H L L H x x x AR column Write dummy channel (auto-restore if AR=H)
L L H H bank row Bank activate
L L H L seg channel seg channel column Prefetch read with auto-precharge (optional)
L L L H x — x — Auto refresh
L L L L reg mode register data Mode register set

The above are the JEDEC-standardized commands. Earlier chips did not support the dummy channel or pair prefetch, and used a different encoding for precharge.

A 13-bit address bus, as illustrated here, is suitable for a device up to 128 Mbit. It would have two banks, each containing 8192 rows and 8192 columns. Thus, row addresses are 13 bits, segment addresses are 2 bits, and 8 column address bits are required to select one byte from the 2048 bits (256 bytes) in a segment.

See also

References

  1. ↑ "SDRAM Part Catalog". 070928 micron.com
  2. ↑ "Nanya 256 Mb DDR SDRAM Datasheet" (PDF). intel.com. April 2003. Retrieved 2015-08-02.
  3. 1 2 3 "EDA DesignLine, januari 12, 2007, The outlook for DRAMs in consumer electronics". 100622 edadesignline.com
  4. ↑ "What is DDR memory?".
  5. ↑ Thomas Soderstrom (June 5, 2007). "Pipe Dreams: Six P35-DDR3 Motherboards Compared". Tom's Hardware.
  6. ↑ "AMD to Adopt DDR3 in Three Years".
  7. ↑ Wesly Fink (July 20, 2007). "Super Talent & TEAM: DDR3-1600 Is Here!". Anandtech.
  8. ↑ Jennifer Johnson (24 April 2012). "G.SKILL Announces DDR3 Memory Kit For Ivy Bridge".
  9. ↑ DDR4 PDF page 23
  10. ↑ "DDR4 not expected until 2015". semiaccurate.com.
  11. ↑ "IDF: "DDR3 won't catch up with DDR2 during 2009"". Alphr.
  12. ↑ "heise online - IT-News, Nachrichten und Hintergründe". heise online.
  13. ↑ "Next-Generation DDR4 Memory to Reach 4.266GHz - Report". Xbitlabs.com. August 16, 2010. Retrieved 2011-01-03.
  14. ↑ "IDF: DDR4 memory targeted for 2012" (in German). hardware-infos.com. Retrieved 2009-06-16. English translation
  15. ↑ "JEDEC Announces Key Attributes of Upcoming DDR4 Standard" (Press release). JEDEC. 2011-08-22. Retrieved 2011-01-06.
  16. ↑ Gruener, Wolfgang (February 4, 2009). "Samsung hints to DDR4 with first validated 40 nm DRAM". tgdaily.com. Retrieved 2009-06-16.
  17. ↑ Jansen, Ng (January 20, 2009). "DDR3 Will be Cheaper, Faster in 2009". dailytech.com. Retrieved 2009-06-17.
  18. ↑ "Samsung Develops Industry's First DDR4 DRAM, Using 30nm Class Technology". Samsung. 2011-01-04. Retrieved 2011-03-13.
  19. ↑ "Samsung develops DDR4 memory, up to 40% more efficient". TechSpot.
  20. ↑ Dean Kent (1998-10-24), RAM Guide: SLDRAM, Tom's Hardware, retrieved 2011-01-01
  21. ↑ Hyundai Electronics (1997-12-20), HYSL8M18D600A 600 Mb/s/pin 8M x 18 SLDRAM (PDF) (data sheet), retrieved 2011-12-27
  22. ↑ SLDRAM Inc. (1998-07-09), SLD4M18DR400 400 Mb/s/pin 4M x 18 SLDRAM (PDF) (data sheet), pp. 32–33, retrieved 2011-12-27
  23. ↑ Siemens Semiconductor Group, HYB39V64x0yT 64MBit Virtual Channel SDRAM (PDF), retrieved 2012-07-17
  24. ↑ NEC (1999), 128M-BIT VirtualChannel™ SDRAM preliminary datasheet (PDF), retrieved 2012-07-17
  25. ↑ JEDEC Standard 21-C section 3.11.5.4 "VCSDRAM Specific SDRAM Functions"

External links

This article is issued from Wikipedia - version of the Friday, May 06, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.