Micro-encapsulation

Micro-encapsulation is a process in which tiny particles or droplets are surrounded by a coating to give small capsules, of many useful properties. In general, it is used to incorporate food ingredients, enzymes, cells or other materials on a micro metric scale. Microencapsulation can also be used to enclose solids, liquids, or gases inside a micrometric wall made of hard or soft soluble film, in order to reduce dosing frequency and prevent the degradation of pharmaceuticals .[1] In a relatively simple form, a microcapsule is a small sphere with a uniform wall around it. The material inside the microcapsule is referred to as the core, internal phase, or fill, whereas the wall is sometimes called a shell, coating, or membrane. Some materials like lipids and polymers, such as alginate, may be used as a mixture to trap the material of interest inside.[2] Most microcapsules have pores with diameters between a few micrometers and a few millimeters. The coating materials generally used for coating are:

The definition has been expanded, and includes most foods, where the encapsulation of flavors is the most common. The technique of microencapsulation depends on the physical and chemical properties of the material to be encapsulated.[3]

Many microcapsules however bear little resemblance to these simple spheres. The core may be a crystal, a jagged adsorbent particle, an emulsion, a Pickering emulsion, a suspension of solids, or a suspension of smaller microcapsules. The microcapsule even may have multiple walls.

IUPAC definition

Microcapsule: Hollow microparticle composed of a solid shell surrounding a
core-forming space available to permanently or temporarily entrapped substances.

Note: The substances can be drugs, pesticides, dyes, etc.[4]

Reasons for encapsulation

The reasons for microencapsulation are countless. It is mainly used to increase the stability and life of the product being encapsulated, facilitate the manipulation of the product and control its liberation in an adequate time and space.[5] In some cases, the core must be isolated from its surroundings, as in isolating vitamins from the deteriorating effects of oxygen, retarding evaporation of a volatile core, improving the handling properties of a sticky material, or isolating a reactive core from chemical attack. In other cases, the objective is not to isolate the core completely but to control the rate at which it leaves the microcapsule, as in the controlled release of drugs or pesticides. The problem may be as simple as masking the taste or odor of the core, or as complex as increasing the selectivity of an adsorption or extraction process. In environmental science, a pesticide may be microencapsulated to minimize leaching or volatilization risks.[6]

Techniques to manufacture microcapsules

Physical methods

Pan coating

The pan coating process, widely used in the pharmaceutical industry, is among the oldest industrial procedures for forming small, coated particles or tablets. The particles are tumbled in a pan or other device while the coating material is applied slowly.

Air-suspension coating

Air-suspension coating, first described by Professor Dale Erwin Wurster at the University of Wisconsin in 1959, gives improved control and flexibility compared to pan coating. In this process the particulate core material, which is solid, is dispersed into the supporting air stream and these suspended particles are coated with polymers in a volatile solvent leaving a very thin layer of polymer on them. This process is repeated several hundred times until the required parameters such as coating thickness, etc., are achieved. The air stream which supports the particles also helps to dry them, and the rate of drying is directly proportional to the temperature of the air stream which can be modified to further affect the properties of the coating.

The re-circulation of the particles in the coating zone portion is effected by the design of the chamber and its operating parameters. The coating chamber is arranged such that the particles pass upwards through the coating zone, then disperse into slower moving air and sink back to the base of the coating chamber, making repeated passes through the coating zone until the desired thickness of coating is achieved.

Centrifugal extrusion

Liquids are encapsulated using a rotating extrusion head containing concentric nozzles. In this process, a jet of core liquid is surrounded by a sheath of wall solution or melt. As the jet moves through the air it breaks, owing to Rayleigh instability, into droplets of core, each coated with the wall solution. While the droplets are in flight, the molten wall may be hardened or a solvent may be evaporated from the wall solution. Since most of the droplets are within ± 10% of the mean diameter, they land in a narrow ring around the spray nozzle. Hence, if needed, the capsules can be hardened after formation by catching them in a ring-shaped hardening bath. This process is excellent for forming particles 400–2,000 µm (16–79 mils) in diameter. Since the drops are formed by the breakup of a liquid jet, the process is only suitable for liquid or slurries. A high production rate can be achieved, up to 22.5 kg (50 lb) of microcapsules can be produced per nozzle per hour. Heads containing 16 nozzles are available.

Vibrational nozzle

Core-shell encapsulation or microgranulation (matrix-encapsulation) can be done using a laminar flow through a nozzle and an additional vibration of the nozzle or the liquid. The vibration has to be done in resonance with the Rayleigh instability and leads to very uniform droplets. The liquid can consist of any liquids with limited viscosities (0-10,000 mPa·s have been shown to work), e.g. solutions, emulsions, suspensions, melts etc. The soldification can be done according to the used gelation system with an internal gelation (e.g. sol-gel processing, melt) or an external (additional binder system, e.g. in a slurry). The process works very well for generating droplets between 20–10,000 µm (0.79–393.70 mils), applications for smaller and larger droplets are known. The units are deployed in industries and research mostly with capacities of 1–20,000 kg per hour (2–44,000 lb/h) at working temperatures of 20–1,500 °C (68–2,732 °F) (room temperature up to molten silicon). Heads are available with from one up to several hundred thousand nozzles.

Spray–drying

Spray drying serves as a microencapsulation technique when an active material is dissolved or suspended in a melt or polymer solution and becomes trapped in the dried particle. The main advantages are the ability to handle labile materials because of the short contact time in the dryer and the operation is economical. In modern spray dryers the viscosity of the solutions to be sprayed can be as high as 300 mPa·s. Applying this technique, along with the use of supercritical carbon dioxide, sensitive materials like proteins can be encapsulated.

Physico-chemical methods

Ionotropic gelation

Ionotropic gelation occurs when units of uric acid in the chains of the polymer alginate, crosslink with multivalent cations. These may include, calcium, zinc, iron and aluminium.[7]

Coacervation-phase separation

Coacervation-phase separation consists of three steps carried out under continuous agitation.

  1. Formation of three immiscible chemical phases: liquid manufacturing vehicle phase, core material phase and coating material phase.
  2. Deposition of coating: core material is dispersed in the coating polymer solution. Coating polymer material coated around core. Deposition of liquid polymer coating around core by polymer adsorbed at the interface formed between core material and vehicle phase.
  3. Rigidization of coating: coating material is immiscible in vehicle phase and is made rigid. This is done by thermal, cross-linking, or dissolution techniques.

Chemical methods

Interfacial polycondensation

In interfacial polycondensation, the two reactants in a polycondensation meet at an interface and react rapidly. The basis of this method is the classical Schotten-Baumann reaction between an acid chloride and a compound containing an active hydrogen atom, such as an amine or alcohol, polyesters, polyurea, polyurethane. Under the right conditions, thin flexible walls form rapidly at the interface. A solution of the pesticide and a diacid chloride are emulsified in water and an aqueous solution containing an amine and a polyfunctional isocyanate is added. Base is present to neutralize the acid formed during the reaction. Condensed polymer walls form instantaneously at the interface of the emulsion droplets.

Interfacial cross-linking

Interfacial cross-linking is derived from interfacial polycondensation, and was developed to avoid the use of toxic diamines, for pharmaceutical or cosmetic applications. In this method, the small bifunctional monomer containing active hydrogen atoms is replaced by a biosourced polymer, like a protein. When the reaction is performed at the interface of an emulsion, the acid chloride reacts with the various functional groups of the protein, leading to the formation of a membrane. The method is very versatile, and the properties of the microcapsules (size, porosity, degradability, mechanical resistance) can be customized.[8] Flow of artificial microcapsules in microfluidic channels:

In-situ polymerization

In a few microencapsulation processes, the direct polymerization of a single monomer is carried out on the particle surface. In one process, e.g. cellulose fibers are encapsulated in polyethylene while immersed in dry toluene. Usual deposition rates are about 0.5μm/min. Coating thickness ranges 0.2–75 µm (0.0079–2.9528 mils). The coating is uniform, even over sharp projections. Protein microcapsules are biocompatible and biodegradable, and the presence of the protein backbone renders the membrane more resistant and elastic than those obtained by interfacial polycondensation.

Matrix polymerization

In a number of processes, a core material is imbedded in a polymeric matrix during formation of the particles. A simple method of this type is spray-drying, in which the particle is formed by evaporation of the solvent from the matrix material. However, the solidification of the matrix also can be caused by a chemical change.

Release methods and patterns

Even when the aim of a microencapsulation application is the isolation of the core from its surrounding, the wall must be ruptured at the time of use. Many walls are ruptured easily by pressure or shear stress, as in the case of breaking dye particles during writing to form a copy. Capsule contents may be released by melting the wall, or dissolving it under particular conditions, as in the case of an enteric drug coating.[9] In other systems, the wall is broken by solvent action, enzyme attack, chemical reaction, hydrolysis, or slow disintegration.

Microencapsulation can be used to slow the release of a drug into the body. This may permit one controlled release dose to substitute for several doses of non-encapsulated drug and also may decrease toxic side effects for some drugs by preventing high initial concentrations in the blood. There is usually a certain desired release pattern. In some cases, it is zero-order, i.e. the release rate is constant. In this case, the microcapsules deliver a fixed amount of drug per minute or hour during the period of their effectiveness. This can occur as long as a solid reservoir or dissolving drug is maintained in the microcapsule.

A more typical release pattern is first-order in which the rate decreases exponentially with time until the drug source is exhausted. In this situation, a fixed amount of drug is in solution inside the microcapsule. The concentration difference between the inside and the outside of the capsule decreases continually as the drug diffuses.

Nevertheless, there are some other mechanisms that may take place in the liberation of the encapsulated material. These include, biodegradation, osmotic pressure, diffusion, etc. Each one will depend on the composition of the capsule made and the environment it is in. Therefore, the liberation of the material may be affected by various mechanisms that act simultaneously.[10]

Applications of microencapsulation

The applications of micro-encapsulation are numerous. The ones mentioned below are some of the most common ones.

References

  1. ↑ López C. Ano., Delaino L., Navarro A.S, & Martino M. (2012) Encapsulación de compuestos bioactivos con alginatos para laindustria de alimentos. Ciencia yTecnología Alimentaria 59(1), 18-27
  2. ↑ Aldana, S.A., Sandoval, R.E. & Aponte, A.A. (2004) Encapsulación de Aditivos para la industria de Alimentos. Ingeniería y competitividad 5(2), 73-83.
  3. ↑ Jackson L. S.; Lee K. (1991-01-01). "Microencapsulation and the food industry". Lebensmittel - Wissenschaft Technologie. Retrieved 1991-02-02. Check date values in: |access-date= (help)
  4. ↑ "Terminology for biorelated polymers and applications (IUPAC Recommendations 2012)" (PDF). Pure and Applied Chemistry 84 (2): 377–410. 2012. doi:10.1351/PAC-REC-10-12-04.
  5. ↑ Élida BH,. (2008). Módulo Materiales Polímeros Retrieved April 1, 2014 at http://www.isabato.edu.ar/ventana_materiales/Gu%C3%ADa-did%C3%A1ctica-pol%C3%ADmeros.pdf.
  6. ↑ Mervosh, T.L.; EW Stoller; FW Simmons; TR Ellsworth; GK Sims (1995). "Effects of starch encapsulation on clomazone and atrazine movement in soil and clomazone volatilization". Weed Science 43: 445–453.
  7. ↑ López C. A., Delaino L., Navarro A.S, & Martino M. (2012) Encapsulación de compuestos bioactivos con alginatos para la industria de alimentos. Ciencia y Tecnología Alimentaria 59(1), 18-27
  8. ↑ Lefebvre Y, Leclerc E, Barthès-Biesel D
  9. ↑ "Medical Dictionary: Enteric coating". freedictionary.com. Retrieved 2009-02-19. External link in |publisher= (help)
  10. ↑ Barba, A.A., d'Amore, M., Chirico,S., Lamberti, G., & Titomalino, G. (2009). A general code to predict the drug release kinetics from different shaped matrices. European Journal of Pharmaceutical Sciences, 36(2-3), 359-368
  11. ↑ R. J. Marathe, A. B. Chaudhari, R. K. Hedaoo, D. Sohn,V. R. Chaudhari,V. V. Gite, Urea formaldehyde (UF) microcapsules loaded with corrosion inhibitor for enhancing the anti-corrosive property of acrylic-based multifunctional PU coatings, RSC Advances, 5, 15539-15546, 2015.
  12. ↑ R. K. Hedaoo,V. V. Gite,Renewable resource-based polymeric microencapsulation of natural pesticide and its release study: an alternative green approach, RSC Advances, 18637- 18644, 2014
  13. ↑ R. K. Hedaoo, P. D. Tatiya, P. P. Mahulikar, V. V. Gite, Fabrication of Dendritic 0G PAMAM-Based Novel Polyurea Microcapsules for Encapsulation of Herbicide and Release Rate from Polymer Shell in Different Environment, Design Monomers and Polymers, 111–125, 2014
  14. ↑ P. D. Tatiya, V. V. Gite, "Novel Polyurea Microcapsules Using Dendritic Functional Monomer: Synthesis, Characterization, and Its Use in Self-healing and Anticorrosive Polyurethane Coatings"Industrial & Engineering Chemistry Research, 52, 1562−1570, 2013.
  15. ↑ Puddu, M.; Paunescu, D.; Stark, W. J.; Grass, R. N. (2014). "Magnetically Recoverable, Thermostable, Hydrophobic DNA/Silica Encapsulates and Their Application as Invisible Oil Tags". ACS Nano 8 (3): 2677. doi:10.1021/nn4063853.
  16. ↑ Grass, R. N.; Heckel, R.; Puddu, M.; Paunescu, D.; Stark, W. J. (2015). "Robust Chemical Preservation of Digital Information on DNA in Silica with Error-Correcting Codes". Angewandte Chemie International Edition 54 (8): 2552. doi:10.1002/anie.201411378.
  17. ↑ Aizpurua-Olaizola, Oier; Navarro, Patricia; Vallejo, Asier; Olivares, Maitane; Etxebarria, Nestor; Usobiaga, Aresatz (2016-01-01). "Microencapsulation and storage stability of polyphenols from Vitis vinifera grape wastes". Food Chemistry 190: 614–621. doi:10.1016/j.foodchem.2015.05.117.

Bibliography

Prakash, S. et al. “The Gut Microbiota and Human Health with an Emphasis on the Use of Microencapsulated Bacterial Cells”, Journal of Biomedicine and Biotechnology (2011),

Brandau, T. "Preparation of monodisperse controlled release microcapsules", Intl. J. Pharm. 242 (2002) 179-184

External links

This article is issued from Wikipedia - version of the Monday, April 25, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.