Woodworking joints

A worker uses a mortising machine to shape timber framing joints

Joinery is a part of woodworking that involves joining together pieces of timber or lumber, to produce more complex items. Some wood joints employ fasteners, bindings, or adhesives, while others use only wood elements. The characteristics of wooden joints - strength, flexibility, toughness, appearance, etc. - derive from the properties of the materials involved and the purpose of the joint. Therefore, different joinery techniques are used to meet differing requirements. For example, the joinery used to construct a house can be different from that used to make puzzle toys, although some concepts overlap.

List of wood joints

A worker uses a large circular saw to cut joints.

Traditional woodworking joints

Joint joint Description
Butt joint The end of a piece of wood is butted against another piece of wood. This is the simplest and weakest joint. Of those, there is the a) T-butt, b) end-to-end butt, c) T-lap d) Miter butt and e) edge-to-edge butt.
Overlap joint see lap joint The end of a piece of wood is laid beside and connected to another piece of wood. This is the next simplest and weakest joint.
Bridle joint
Also known as open tenon, open mortise and tenon, or tongue and fork joints, this joint is where the through mortise is open on one side and forms a fork shape. The mate has a through tenon or necked joint. Bridle joints are commonly used to join rafter tops, also used in scarf joints and sometimes sill corner joints in timber framing.
Dowel joint
The end of a piece of wood is butted against another piece of wood. This is reinforced with dowel pins. This joint is quick to make with production line machinery and so is a very common joint in factory-made furniture.
Mitre joint
Similar to a butt joint, but both pieces have been bevelled (usually at a 45 degree angle).
Finger joint
Also known as a box joint, is a corner joint with interlocking fingers. Receives pressure from two directions.
Dovetail joint
A form of box joint where the fingers are locked together by diagonal cuts. More secure than a finger joint.
Dado joint
Also called a housing joint or trench joint, a slot is cut across the grain in one piece for another piece to set into; shelves on a bookshelf having slots cut into the sides of the shelf, for example.
Groove joint
Like the dado joint, except that the slot is cut with the grain.
Tongue and groove
Each piece has a groove cut all along one edge, and a thin, deep ridge (the tongue) on the opposite edge. If the tongue is unattached, it is considered a spline joint.
Mortise and tenon
A stub (the tenon) will fit tightly into a hole cut for it (the mortise). This is a hallmark of Mission Style furniture, and also the traditional method of jointing frame and panel members in doors, windows, and cabinets. This joint is a good strong joint to use.
Birdsmouth joint
Also called a bird's beak cut, this joint used in roof construction. A V-shaped cut in the rafter connects the rafter to the wall-plate.[1]
Cross Lap
A joint in which the two members are joined by removing material from each at the point of intersection so that they overlap.
Splice joint
A joint used to attach two members end to end.

Nontraditional woodworking joints

- Joint Image Description
Wooden (or integral) connectors Pocket hole joinery
A hidden screw is driven into the joint at an angle.
biscuit A wooden disc is driven into the joint at an angle.
Metal connectors Joints using metal connectors that attach to the frame with nails or screws.
Floating tenon joint See Mortise and tenon
stitch and glue

Traditional ways of improving joints

A doweled joint

Nontraditional ways of improving joints

Properties of wood

Many wood joinery techniques either depend upon or compensate for the fact that wood is anisotropic: its material properties are different along different dimensions.

This must be taken into account when joining wood parts together, otherwise the joint is destined to fail. Gluing boards with the grain running perpendicular to each other is often the reason for split boards, or broken joints. Furniture from the 18th century, while made by master craftsmen, did not take this into account. The result is this masterful work suffers from broken bracket feet, which was often attached with a glue block which ran perpendicular to the base pieces. The glue blocks were fastened with both glue and nails, resulting in unequal expansion and contraction between the pieces. This was also the cause of splitting of wide boards, which were commonly used during that period.

In modern woodworking it is even more critical, as heating and air conditioning cause major changes in the moisture content of the wood. All woodworking joints must take these changes into account, and allow for the resulting movement.[2]

Strength

Wood is stronger when stressed along the grain (longitudinally) than it is when stressed across the grain (radially and tangentially). Wood is a natural composite material; parallel strands of cellulose fibers are held together by a lignin binder. These long chains of fibers make the wood exceptionally strong by resisting stress and spreading the load over the length of the board. Furthermore, cellulose is tougher than lignin, a fact demonstrated by the relative ease with which wood can be split along the grain compared to across it.

Different species of wood have different strength levels, and the exact strength may vary from sample to sample.

Dimensional stability

Timber expands and contracts in response to humidity, usually much less so longitudinally than in the radial and tangential directions. As tracheophytes, trees have lignified tissues which transport resources such as water, minerals and photosynthetic products up and down the plant. While lumber from a harvested tree is no longer alive, these tissues still absorb and expel water causing swelling and shrinkage of the wood in kind with change in humidity.[3] When the dimensional stability of the wood is paramount, quarter-sawn or rift-sawn lumber is preferred because its grain pattern is consistent and thus reacts less to humidity.

Materials used for joining

Metal plates are often incorporated into the design where the timber alone would not be strong enough for a given load.
Pin-connected post and beam house framing

Traditional joinery

Many traditional wood joinery techniques use the distinctive material properties of wood, often without resorting to mechanical fasteners or adhesives. While every culture in which pieces of wood are joined together to make furniture or structures has a joinery tradition, wood joinery techniques have been especially well documented and celebrated in the Indian, Chinese, European, and Japanese traditions. Because of the actual physical existence of Indian and Egyptian examples, we know that furniture from the first several dynasties show the use of complex joints, like the Dovetail, over 5 thousand years ago. This tradition continued to other later Western styles. The 18th century writer Diderot included over 90 detailed illustrations of wood joints in his comprehensive encyclopedia.[4] While Western techniques focused on concealment of joinery, the Eastern societies, though later, did not attempt to "hide" their joints. The Japanese and Chinese traditions in particular required the use of hundreds of types of joints. The reason was that nails and glues used did not stand up well to the vastly fluctuating temperatures and humid weather conditions in most of Central and South-East Asia.[5] As well, the highly resinous woods used in traditional Chinese furniture do not glue well, even if they are pre-cleaned with solvents and attached using modern glues.

Nontraditional joinery

Methods that are not considered traditional joinery have come about in modern times, largely to attempt to simplify the job of the woodworker for various reasons. These include biscuit joints and pocket hole joinery.

See also

Footnotes

  1. ↑ http://sawdustmaking.com/woodjoints/misc.htm
  2. ↑ Pro Woodworking Tips.com
  3. ↑ Wood Movement, WoodworkDetails.com
  4. ↑ Diderot, Denis. "l'Encyclopedie". The Encyclopedia of Diderot & d'Alembert. Retrieved 1 April 2015.
  5. ↑ Huntley, Michael (20 January 2009), "Michael Huntley demystifies the furniture making techniques of Chinese craftsmen prior to 1900", Wood Worker's Institute (GMC Publications)

References

External links

Wikibooks has a book on the topic of: Carpentry/Cabinetry/Joints
Wikimedia Commons has media related to Woodworking joinery.
Terms and Joints
This article is issued from Wikipedia - version of the Thursday, March 10, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.