Sulfur trioxide
| |||
| Names | |||
|---|---|---|---|
| Preferred IUPAC name
Sulfur trioxide | |||
| Systematic IUPAC name
Sulfonylideneoxidane | |||
| Other names
Sulfuric anhydride | |||
| Identifiers | |||
7446-11-9  | |||
| ChEBI | CHEBI:29384 | ||
| ChemSpider | 23080 | ||
| EC Number | 231-197-3 | ||
| 1448 | |||
| Jmol 3D model | Interactive image | ||
| PubChem | 24682 22235242 (hemihydrate) 23035042 (monohydrate) | ||
| RTECS number | WT4830000 | ||
| UN number | UN 1829 | ||
| |||
| |||
| Properties | |||
| SO3 | |||
| Molar mass | 80.066 g/mol | ||
| Density | 1.92 g/cm3, liquid | ||
| Melting point | 16.9 °C (62.4 °F; 290.0 K) | ||
| Boiling point | 45 °C (113 °F; 318 K) | ||
| Reacts to give sulfuric acid | |||
| Thermochemistry | |||
| Std molar entropy (S |
256.77 J K−1 mol−1 | ||
| Std enthalpy of formation (ΔfH |
−395.7 kJ/mol | ||
| Hazards | |||
| Safety data sheet | ICSC 1202 | ||
| EU classification (DSD) |
 O (O) | ||
| R-phrases | R14, R35, R37 | ||
| S-phrases | (S1/2), S26, S30, S45, S53 | ||
| NFPA 704 | |||
| Flash point | Non-flammable | ||
| Lethal dose or concentration (LD, LC): | |||
| LC50 (Median concentration) |
rat, 4hr 375 mg/m3 | ||
| Related compounds | |||
| Other cations |
Selenium trioxide Tellurium trioxide | ||
| Sulfur monoxide Sulfur dioxide | |||
| Related compounds |
Sulfuric acid | ||
| Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa). | |||
 verify (what is ?) | |||
| Infobox references | |||
Sulfur trioxide (alternative spelling sulphur trioxide) is the chemical compound with the formula SO3. In the gaseous form, this species is a significant pollutant, being the primary agent in acid rain.[1] It is prepared on an industrial scale as a precursor to sulfuric acid.
Structure and bonding
Gaseous SO3 is a trigonal planar molecule of D3h symmetry, as predicted by VSEPR theory. SO3 belongs to the D3h point group.
In terms of electron-counting formalism, the sulfur atom has an oxidation state of +6 and a formal charge of +2. The Lewis structure consists of an S=O double bond and two S–O dative bonds without utilizing d-orbitals.[2]
The electrical dipole moment of gaseous sulfur trioxide is zero. This is a consequence of the 120° angle between the S-O bonds.
Chemical reactions
SO3 is the anhydride of H2SO4. Thus, the following reaction occurs:
The reaction occurs both rapidly and exothermically, too violently to be used in large-scale manufacturing. At or above 340 °C, sulfuric acid, sulfur trioxide, and water coexist in significant equilibrium concentrations.
Sulfur trioxide also reacts with sulfur dichloride to yield the useful reagent, thionyl chloride.
- SO3 + SCl2 → SOCl2 + SO2
SO3 is a strong Lewis acid readily forming crystalline complexes with pyridine, dioxane and trimethylamine which can be used as sulfonating agents.[4]
Preparation
Sulfur trioxide can be prepared in the laboratory by the two-stage pyrolysis of sodium bisulfate. Sodium pyrosulfate is an intermediate product:[5]
- Dehydration at 315 °C:
- 2 NaHSO4 → Na2S2O7 + H2O
- Cracking at 460 °C:
- Na2S2O7 → Na2SO4 + SO3
This method will not work or will give a low yield for other metal bisulfates, particularly for potassium salt, because it easily gives away sulfur dioxide first, converting into dipotassium peroxymonosulfate, while the equivalent compound for sodium seems to be too unstable to form.[5]
Industrially SO3 is made by the contact process. Sulfur dioxide, generally made by the burning of sulfur or iron pyrite (a sulfide ore of iron), is first purified by electrostatic precipitation. The purified SO2 is then oxidised by atmospheric oxygen at between 400 and 600 °C over a catalyst consisting of vanadium pentoxide (V2O5) activated with potassium oxide K2O on kieselguhr or silica support. Platinum also works very well but is too expensive and is poisoned (rendered ineffective) much more easily by impurities.
The majority of sulphur trioxide made in this way is converted into sulfuric acid not by the direct addition of water, with which it forms a fine mist, but by absorption in concentrated sulfuric acid and dilution with water of the produced oleum.
Structure of solid SO3
The nature of solid SO3 is a surprisingly complex area because of structural changes caused by traces of water.[6] Upon condensation of the gas, absolutely pure SO3 condenses into a trimer, which is often called γ-SO3. This molecular form is a colorless solid with a melting point of 16.8 °C. It adopts a cyclic structure described as [S(=O)2(μ-O)]3.[7]
If SO3 is condensed above 27 °C, then α-SO3 forms, which has a melting point of 62.3 °C. α-SO3 is fibrous in appearance. Structurally, it is the polymer [S(=O)2(μ-O)]n. Each end of the polymer is terminated with OH groups. β-SO3, like the alpha form, is fibrous but of different molecular weight, consisting of an hydroxyl-capped polymer, but melts at 32.5 °C. Both the gamma and the beta forms are metastable, eventually converting to the stable alpha form if left standing for sufficient time. This conversion is caused by traces of water.[8]
Relative vapor pressures of solid SO3 are alpha < beta < gamma at identical temperatures, indicative of their relative molecular weights. Liquid sulfur trioxide has a vapor pressure consistent with the gamma form. Thus heating a crystal of α-SO3 to its melting point results in a sudden increase in vapor pressure, which can be forceful enough to shatter a glass vessel in which it is heated. This effect is known as the "alpha explosion".[8]
SO3 is aggressively hygroscopic. The heat of hydration is sufficient that mixtures of SO3 and wood or cotton can ignite. In such cases, SO3 dehydrates these carbohydrates.[8]
Application
In process plant environment, SO3 gas is mixed into flue gas from combustion to give any particulates an electrostatic charge before they pass through electrostatic precipitators. The electrostatic precipitators will then trap the particulates, making cleaner process emission possible.
Safety
Sulfur trioxide will cause serious burns on both inhalation and ingestion because it is highly corrosive and hygroscopic in nature. SO3 should be handled with extreme care as it reacts with water violently and produces highly corrosive sulfuric acid.
Sources
See also
References
- ↑ Thomas Loerting, Klaus R. Liedl (2000). "Toward elimination of descrepancies between theory and experiment: The rate constant of the atmospheric conversion of SO3 to H2SO4". Proceedings of the National Academy of Sciences of the United States of America 97 (16): 8874–8878. doi:10.1073/pnas.97.16.8874.
- ↑ Terence P. Cunningham , David L. Cooper , Joseph Gerratt , Peter B. Karadakov and Mario Raimondi (1997). "Chemical bonding in oxofluorides of hypercoordinatesulfur". Journal of the Chemical Society, Faraday Transactions 93 (13): 2247–2254. doi:10.1039/A700708F.
- ↑ http://nzic.org.nz/ChemProcesses/production/1B.pdf
- ↑ Cotton, F. Albert; Wilkinson, Geoffrey; Murillo, Carlos A.; Bochmann, Manfred (1999), Advanced Inorganic Chemistry (6th ed.), New York: Wiley-Interscience, ISBN 0-471-19957-5
- 1 2 http://doc.utwente.nl/68103/1/Vries69thermal.pdf
- ↑ Holleman, A. F.; Wiberg, E. (2001), Inorganic Chemistry, San Diego: Academic Press, ISBN 0-12-352651-5
- ↑ Advanced Inorganic Chemistry by Cotton and Wilkinson, 2nd ed p543
- 1 2 3 Merck Index of Chemicals and Drugs, 9th ed. monograph 8775
| ||||||||||