South African Class C 4-6-0T

NGR Kitson 2-6-0T
NGR Class G 4-6-0T
South African Class C 4-6-0T

NGR Class G no. 26
Type and origin
♠ - 2-6-0T configuration, as built
- 4-6-0T configuration, modified or as built
Power type Steam
Designer Kitson and Company
Builder Kitson and Company
Robert Stephenson and Company
Serial number Kitson 2254-2258, 2269-2270, 2358-2360, 2504-2508, 2898-2900
Stephenson 2484-2490, 2519-2520, 2571-2580
Model NGR Class G
Build date 1879-1885
Total produced 37
Rebuilder Natal Government Railways
Rebuild date 1883, 1896 & 1902
Number rebuilt 1883: 7 to 4-6-0T (Ten-wheeler)
1896: 1 to 4-6-4T (Baltic)
1902: 1 to 4-6-2T (Pacific)
Specifications
Configuration ♠ 7 built as 2-6-0T (Mogul)
30 built as 4-6-0T (Ten-wheeler)
Driver 2nd coupled axle
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Leading dia. ♠ 24 in (610 mm)
25 34 in (654 mm)
Coupled dia. ♠ 38 in (965 mm)
39 in (991 mm)
Wheelbase ♠ 14 ft 1 in (4,293 mm)
16 ft 8 14 in (5,086 mm)
  Leading 5 ft (1,524 mm)
  Coupled 7 ft 9 in (2,362 mm)
Wheel spacing
(Assymetrical)
1-2: 3 ft 7 12 in (1,105 mm)
2-3: 4 ft 1 12 in (1,257 mm)
Length:
  Over couplers ♠ 24 ft (290 in)
26 ft 34 in (7,944 mm)
  Over beams ♠ 21 ft 9 58 in (6,645 mm)
23 ft 10 38 in (7,274 mm)
Height 11 ft 7 14 in (3,537 mm)
Frame type Plate
Axle load 8 LT 4 cwt (8,332 kg)
  Leading 5 LT 18 cwt (5,995 kg)
  1st coupled 7 LT 14 cwt (7,824 kg)
  2nd coupled 8 LT 4 cwt (8,332 kg)
  3rd coupled 7 LT 6 cwt (7,417 kg)
Adhesive weight 23 LT 4 cwt (23,570 kg)
Loco weight 29 LT 2 cwt (29,570 kg)
Fuel type Coal
Fuel capacity ♠ 1 LT 5 cwt (1.3 t)
1 LT (1.0 t)
Water cap 700 imp gal (3,180 l)
Firebox type Round-top
  Firegrate area 11 sq ft (1.0 m2)
Boiler:
  Pitch 5 ft 7 in (1,702 mm)
  Diameter 3 ft 4 34 in (1,035 mm)
  Tube plates 10 ft 3 12 in (3,137 mm)
  Small tubes 130: 1 34 in (44 mm)
Boiler pressure ♠ 140 psi (965 kPa)
175 psi (1,207 kPa) reboilered
Safety valve Salter
Heating surface 669 sq ft (62.2 m2)
  Tubes 611 sq ft (56.8 m2)
  Firebox 58 sq ft (5.4 m2)
Cylinders Two
Cylinder size 14 in (356 mm) bore
21 in (533 mm) stroke
Valve gear Stephenson
Valve type Slide, flat type
Couplers Bell link-and-pin
Performance figures
Tractive effort ♠ 11,080 lbf (49.3 kN) @ 75%
13,850 lbf (61.6 kN) @ 75%
Career
Operators Natal Government Railways
South African Railways
Eskom
Class NGR Class G, SAR Class C
Number in class NGR 37, SAR 15
Numbers NGR 8-14, 16-26, 29-47
SAR 62-76
Delivered 1879-1885
First run 1879
Withdrawn 1940

The South African Railways Class C 4-6-0T of 1879 was a steam locomotive from the pre-Union era in the Natal Colony.

Between 1879 and 1885, the Natal Government Railways placed thirty-seven 4-6-0 Ten-wheeler type tank steam locomotives in service. Of these, the first seven were built as 2-6-0T Mogul type locomotives and were subsequently modified to a 4-6-0T wheel arrangement. They were designated Class G and, in 1912, when fifteen of them were assimilated into the South African Railways, they were renumbered and reclassified to Class C.[1][2][3][4]

Origins

In 1875, when the Natal Government took over all the assets of the Natal Railway Company and formed the Natal Government Railways (NGR), two important decisions were made. The first was to extend the tracks inland from Durban to Pietermaritzburg to open up the line into the interior, and to Verulam on the North Coast and Isipingo on the South Coast to serve the growing farming communities up and down the coast from Durban. The second was to convert the railway from broad gauge to Cape gauge, to conform to the gauge used by the Cape Government Railways. This decision to regauge was most likely brought about by the terrain which confronted the new railway in the Natal interior, which would demand heavy grades and tight curves.[5]

The first Cape gauge locomotives of the NGR were seven Class K 2-6-0T engines which had been ordered from Beyer, Peacock and Company in 1877, to meet the expected traffic demands on these new lines. They were built to the same specifications as the engines Durban and Pietermaritzburg, a pair of 2-6-0T locomotives which were built by Kitson and Company for Wythes and Jackson, the contractors who built the line between Durban and Pietermaritzburg.[5]

Manufacturers

The NGR Class G was a development of those first Cape gauge Class K 2-6-0 tank locomotives. These new locomotives were initially often referred to as the K&S Class, after their builders, Kitson and Company and Robert Stephenson and Company, until a classification system was introduced by the NGR at some stage between 1904 and 1908 and they were designated the NGR Class G. Altogether thirty-seven were built by these two manufacturers, in six batches between 1879 and 1885.[2][4][5][6]

1879
Works picture of NGR Class G no. 8

The first seven of these locomotives were delivered from Kitson in 1879, with works numbers in the range from 2254 to 2258, 2269 and 2270. They were numbered in the range from 8 to 14. Like their predecessor Class K, these seven locomotives were built with a 2-6-0T Mogul type wheel arrangement. They were all soon rebuilt to a 4-6-0 Ten-wheeler type wheel arrangement, probably beginning in 1882, since mention is made in the NGR Annual Report for 1883 of five locomotives of the 1879 order having been rebuilt in this manner during the year covered in the report. In the process, the locomotive frame had to be extended forward by 24 34 inches (629 millimetres) to accommodate the four-wheeled bogie.[1][5][7]

1880
Works picture, NGR Class G no. 16

Three more locomotives followed in 1880, also built by Kitson, with works numbers in the range from 2358 to 2360 and numbered in the range from 16 to 18. These three, as well as all those which followed, were built with a 4-6-0 Ten-wheeler type wheel arrangement. In order to accommodate the bogie, these and the following locomotives were all 23 feet 10 38 inches (7.274 metres) long over their buffer beams, compared to the 21 feet 9 58 inches (6.645 metres) length of the locomotives of 1879.[1][5][7]

1882

Twelve more followed in 1882, of which five were built by Kitson, with works numbers in the range from 2504 to 2508 and numbered in the range from 22 to 26. The rest were built by Robert Stephenson and Company, with works numbers in the range from 2484 to 2490. Their known engine numbers (see table below) indicate that they were not numbered in chronological order and that some of them were allocated numbers from earlier locomotives which may have been withdrawn or renumbered.[5][7]

1883

Two locomotives were delivered in 1883, built by Stephenson with works numbers 2519 and 2520. Their known numbers also indicate renumbering and gap-filling on the locomotive numbering roster.[5][7]

1884

Ten locomotives were delivered in 1884, built by Stephenson, with works numbers in the range from 2571 to 2580 and numbered in the range from 32 to 41.[5][7]

1885

The last three were built by Kitson, with works numbers in the range from 2898 to 2900 and numbered in the range from 42 to 44.[5][7]

Characteristics

The locomotive was able to haul a maximum load of 90 long tons (91.4 tonnes) on 1 in 30 (3⅓%) grades with curves of 300 feet (91 metres) radius.[2]

Two small two-axle water tenders with a 6 feet (1,829 millimetres) wheelbase, for use on long runs, were supplied by Kitson. Another two-axle tender with a 7 feet (2,134 millimetres) wheelbase was built in the Durban workshops in 1882, to the design of Locomotive Superintendent William Milne. In contrast to the Cape Government Railways (CGR), where tender locomotives were acquired for mainline work from the outset, the NGR persisted with side-tank locomotives on mainline work until 1904, in spite of their inherent limited coal and water capacities.[2]

Modifications

Several modifications were done to many of these locomotives during their years in service. This led to differences between locomotives in one or more of several aspects.[1]

Rebuiding

To 4-6-4T Baltic

Two of these locomotives were rebuilt by G.W. Reid, who was appointed as Locomotive Superintendent of the NGR on 1 July 1893. No. 21 was rebuilt to a 4-6-4T Baltic type wheel arrangement in 1896, for use on the South Coast line. At the time, there was no turning facility at the end of this line and the modification was made to enable the locomotive to run equally well in either direction. This locomotive was later renumbered 39 and designated NGR Class H.[2][5][8]

To 4-6-2T Pacific

In 1901, no. 25 was rebuilt to a 4-6-2T Pacific type wheel arrangement. This locomotive was later renumbered 38. Both these rebuilt locomotives were designated NGR Class H when a classification system was introduced on the NGR.[2][5][6]

Service

Natal Government Railways

In NGR service, the Class G replaced the slightly smaller Beyer, Peacock-built Class K 2-6-0 tank locomotives on mainline trains out of Durban. They were occasionally used with the small four-wheeled tenders, to increase their water carrying capacity when they were required to work long distances.[4]

South African Railways

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, NGR and Central South African Railways) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.[3][9]

In 1912, fifteen survivors of the Class G became the South African Railways (SAR) Class C and were renumbered in the range from 62 to 76. These were the oldest locomotives to be reclassified and renumbered onto the SAR roster. All older and some newer locomotives which were in service at the time, were considered obsolete and were renumbered by having the numeral "0" prefixed to their existing numbers. In SAR service, the Class C locomotives were used as shunting engines until the last one was withdrawn from service in 1940.[3][4][5]

Electricity Supply Commission

In post-SAR service, one of the ex 2-6-0T rebuilt locomotives, Kitson works number 2269 of 1879, remained in service with the Electricity Supply Commission (Eskom) until the mid-1980s, by which time it had rendered more than 105 years of service. While in Eskom's service, it was named Kitty after its builder, Kitson. The engine was declared a heritage object in 1983. The relevant gazette of the South African Heritage Resources Agency (SAHRA), no. 8682 of 29 April 1983, describes it as the oldest working steam locomotive in South Africa and the first to have completed a century of service.[4][10][11]

Renumbering

The early locomotive numbering practices which were followed on the NGR, still remain to be deciphered. It would appear that locomotives which were taken out of mainline service, were renumbered into the 500 number range. Number slots which became vacant in this manner, or as a result of locomotive withdrawal, sale or scrapping, were then re-used, either by being allocated to new locomotives or by wholesale renumbering. The published number lists all appear to be snapshots at a point in time and none appear to present the complete picture. The numbers, as listed in the table below, are from two sources, those presented by D.F. Holland in his publication of 1971 and those presented by R.V. Conyngham in his booklet of 1995. The two sources are indicated in the table headings below by "DFH" or "RVC" respectively, with the differences between the two sources shaded yellow.[1][3][5][7][12]

On two of the three SAR numbers where the Holland and Conyngham lists disagree, the official "Classification of S.A.R. Engines with Renumbering Lists issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912" seems to prove Holland correct, as shown, shaded green, in the Notes column in the table. This official document shows old and new numbers, but not builder's works numbers.[3]

On the third disagreement, historic records show two locomotives which bore the number 47. Here, Conyngham is presumed to be correct, since the locomotive Kitty is known to have been built by Kitson, not Stephenson.[1]

Illustration

References

  1. 1 2 3 4 5 6 7 8 The "K&S" Class Locomotives of the Natal Government Railways. Conyngham, Ron V., RHG. Fish Hoek, 28 December 1995.
  2. 1 2 3 4 5 6 7 Espitalier, T.J.; Day, W.A.J. (1944). The Locomotive in South Africa - A Brief History of Railway Development. Chapter III - Natal Government Railways. South African Railways and Harbours Magazine, May 1944. pp. 339-340.
  3. 1 2 3 4 5 Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912, pp. 7, 13, 19 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)
  4. 1 2 3 4 5 Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 10–11, 28. ISBN 0869772112.
  5. 1 2 3 4 5 6 7 8 9 10 11 12 13 Holland, D.F. (1971). Steam Locomotives of the South African Railways, Volume 1: 1859-1910 (1st ed.). Newton Abbott, Devon: David & Charles. pp. 87–89. ISBN 978-0-7153-5382-0.
  6. 1 2 The Railway Report for year ending 31 Dec. 1908, Natal Government Railways, p. 39, par 14.
  7. 1 2 3 4 5 6 7 NGR Class G numbering
  8. NGR appointment dates - W. Milne & G.W. Reid
  9. The South African Railways - Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, p. 25.
  10. Middleton, John N. (2002). Railways of Southern Africa Locomotive Guide - 2002 (as amended by Combined Amendment List 4, January 2009) (2nd, Dec 2002 ed.). Herts, England: Beyer-Garratt Publications. p. 15.
  11. "Kitty Steam Locomotive, SA National Railway and Steam Museum, Krugersdorp". South African Heritage Resource Agency. Retrieved 23 July 2011.
  12. The Railway Report for year ending 31 Dec. 1880, Natal Government Railways, p. JJ72.
Wikimedia Commons has media related to South African Class C (4-6-0T).
This article is issued from Wikipedia - version of the Thursday, April 28, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.